20
RQT0A22
To check this system’s IP address or the Wi-Fi MAC
address.
1
Press [RADIO/EXT-IN]
repeatedly to select
“NETWORK”.
2
Press [SETUP] repeatedly to select “NET INFO”
and then press [OK].
3
Press [
3
,
4
] repeatedly to select “IP ADDR.” or
“MAC ADDR.” and then press [OK].
The IP address or the MAC address is partially
displayed.
4
Press [
3
,
4
] on the remote control to show the
rest of the IP address or the MAC address.
≥
Press [OK] to exit.
≥
The “ – ” displayed on the top or bottom left of the
display indicate the first and last units respectively.
To reset the network settings.
1
Press [RADIO/EXT-IN] repeatedly to select
“NETWORK”.
2
Press [SETUP] repeatedly to select “NET RESET”
and then press [OK].
3
Press [
3
,
4
] to select “OK? YES” and then press
[OK].
≥
“NETWORK INITIALIZING” is indicated on the display.
When the display returns to “NETWORK”, the network
settings are reset.
≥
This function does not affect the “WIRELESS LAN” setting.
Troubleshooting
Before requesting service, make the following checks.
If you are uncertain about some of the check points, or
if the solutions indicated in the following guide does not
resolve the issue, then consult your dealer for
instructions.
Humming heard during playback.
≥
If an AC mains lead or fluorescent lights are near the cords, then
keep other appliances and cords away from the cables.
The unit does not work.
≥
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1
Touch [
Í
/I] on the unit to switch the unit to standby.
≥
If the unit does not switch to standby, touch [
∫
] on the unit
for approximately 10 seconds. The unit is forcibly switched
to standby. Alternatively, disconnect the AC mains lead, wait
for at least 3 minutes, then reconnect it.
2
Touch [
Í
/I] on the unit to switch it on. If the unit still cannot be
operated, consult the dealer.
MP3 cannot be read.
≥
You may not be able to play MP3 if you have copied a
multi-session disc that has no data between sessions.
≥
When creating a multi-session disc, it is necessary to close the
session.
≥
The amount of data on the disc is too small. Set the amount of
data to above 5 MB.
Charging does not start during standby mode.
≥
Turn the unit on. Check the charging has started, and then turn
the unit to standby mode. (
l
6)
Noise is heard.
≥
When a device is connected to both the AUX IN jack and the DC
OUT terminal, noise may be generated depending on the device.
In this case, remove the USB cable from the DC OUT terminal.
The switches on the unit do not work.
≥
The switches on the unit are touch keys. Touch the switches with
your finger. They may not work if operated with your fingernails or
hands wearing gloves.
IP/MAC Address
Network reset
To return all settings to the factory defaults
When the following situations occur, reset the
memory:
≥
You want to clear and reset the memory contents.
1
Touch and hold [
Í
/I] on the unit until “RESET?”
appears on the display.
2
While touching and holding down [
Í
/I] on the
unit, touch [SELECTOR] on the unit.
“RESET” appears on the display and all the indicators
flash. After “---------” is displayed, the unit will turn off.
≥
The settings are returned to the factory defaults. It is
necessary to set the memory items again.
≥
To reset the network settings, perform the operation for
network reset. (
l
left)
General
SC-ALL5CD-EGEBGN~RQT0A22.book 20 ページ ２０１５年７月１７日 金曜日 午前１１時３０分
