Panasonic SA-AK570GCP Servise Manual Download Page 2

Page: 2 / 134

Wow and flutter

0.18 % (WRMS)

Fast forward and rewind time

Approx. 120 seconds with C-60 cassette tape

■

DISC SECTION

Disc played [8 cm or 12 cm]

(1) CD-Audio (CD-DA)

(2) CD-R/RW (CD-DA, MP3* formatted disc)

(3) MP3*

* MPEG-1 Layer 3, MPEG-2 Layer 3

Pick up

Wavelength

780 nm

Beam Source

Semiconductor laser

Audio output (Disc)

Number of channel

2 (FL, FR)

FL = Front left channel

FR = Front right channel

■

USB SECTION

USB Port

USB Standard

USB 2.0 full speed

Media file format support

MP3 (*.mp3)

USB device file system

FAT 12

FAT 16

FAT 32

USB port power

500 mA (Max)

USB Ripping (recording)

Recording file format

Safety Precautions

Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Handling Precautions for Traverse Unit

Precaution of Laser Diode

About Lead Free Solder (PbF)

Operation Procedures

Self diagnosis and special mode setting

Assembling and Disassembling

Disassembly and Assembly of Traverse Unit Assembly in

Play Position

10 Service Fixture and Tools

11 Service Positions

MP3 (*.mp3)

Bit rate

128 kbps / 192 kbps / 320 kbps

USB recording speed

1x, max 4x (CD only)

■

GENERAL

Power supply

AC 120 V, 60Hz (PL only)

AC 110 to 127/220 to 240 V, 50/60 Hz (GCP only)

Power consumption

141 W (PL Only)

124 W (GCP Only)

Dimensions (WxHxD)

250x331x334 mm

Mass

4.9 kg

Operating temperature range

0 to 40°C

Operating humidity range

35 to 80% RH (no condensation)

Power consumption in standby mode:

0.3 W (approx.) (PL only)

0.5 W (approx.) (GCP only)

■

SYSTEM

SC-AK570 (PL)

Music center: SA-AK570 (PL)

Speaker: SB-AK570 (PL)

SC-AK570 (GCP)

Music center: SA-AK570 (GCP)

Speaker: SB-AK570 (PL)

For information on speaker system, please refer to the original
Service Manual (Order No. MD0805011CE) for SB-AK570PL-K.

Notes:

Specifications are subject to change without notice. Mass and
dimensions are approximate.

Total harmonic distortion is measured by the digital spectrum
analyzer.

12 Procedure for Checking Operation of Individual Parts of Deck

Mechanism Unit

13 Measurement And Adjustments

14 Voltage Measurement and Waveform Chart

15 Wiring Connection Diagram

16 Block Diagram

17 Notes Of Schematic Diagram

18 Schematic Diagram

19 Printed Circuit Board

105

20 Illustration of ICs, Transistors and Diodes

113

21 Terminal Function of Integrated Circuits

114

22 Exploded Views

117

23 Replacement Parts List

121

CONTENTS

Page

SA-AK570PL / SA-AK570GCP

Summary of Contents for SA-AK570GCP







































































































































Search results

Summary of Contents for SA-AK570GCP

Reviews:

Related manuals for SA-AK570GCP

Brands by name

Popular brands

Panasonic SA-AK570GCP, Servise Manual

Search results

Summary of Contents for SA-AK570GCP

Reviews:

Related manuals for SA-AK570GCP

Brands by name

Popular brands