Panasonic S-22ML1E5 Service Manual & Test Run Service Manual Download Page 173

Page: 173 / 175

Mini VRF SYSTEM

Test Run

7 - 19

7. Self-Diagnosis Function Table and Contents of Alarm Display

• Contents of alarm display on remote controller

For the remote controller, there are other alarm contents listed on the following table besides the alarm display on outdoor main unit
control P.C. board.

Wired remote

control display

Detected contents

<E01>

Remote controller is detecting error signal from indoor unit.

Indoor unit does not respond to remote controller.

<E02>

Remote controller is having error in sending serial

communication signal.

<<E03>>

Remote controller does not respond to indoor unit.

E04

Remote controller is detecting error signal from outdoor

unit.

Outdoor unit does not respond to indoor unit.

E08

Improper setting

Indoor unit address is dupulicating.

<<E09>>

Two or more remote controllers are set as main on R1-R2

link.

E18

Indoor unit communication error in group control wiring

No response from sub indoor to the main indoor unit in

group control wiring.

<<L02>>

Improper setting

Indoor unit model does not match with the outdoor unit

model. (Multi-split/mini-split)

<L03>

Two or more indoor units are set as main in group control.

L07

Group control wiring is detected for indoor unit set as

individual control.

L08

Indoor unit address is not set.

<<L09>>

Capacity setting of indoor unit is not correct.

<<F01>>

Indoor unit sensor has failure

Indoor unit heat exchanger liquid temperature sensor has

failure. (E1)

<<F03>>

Indoor unit heat exchanger gas temperature sensor has

failure. (E3)

<<F10>>

Indoor suction air (room) temperature sensor has failure.

(TA)

<<F11>>

Indoor discharge air temperature sensor has failure. (BL)

<<P09>>

Connection to the panel of indoor unit is not good.

<<P01>>

Activation of protective device for Indoor unit

Thermal protector for Indoor unit fan motor is activated.

<<P10>>

Float switch of drain pan safety is activated.

<<P11>>

Drain pump failure or locked rotor.

<<P12>>

Indoor unit fan inverter protection control is activated.

F29

EEPROM on indoor unit PCB has failure.

• The parentheses of << >> used in the table of alarm display does not affect anything the operation of other indoor units.
• The parentheses of < > used in the table of alarm display implies that there are two cases : according to the content of the symptom,

some affect the operation of other indoor units and others do not affect anything.

Alarm messages displayed on system controller

Serial

communication

errors

Mis-setting

Error in transmitting serial

communication signal

Indoor or main outdoor unit is not operating correctly.

Mis-wiring of control wiring between indoor unit, main outdoor unit and

system controller.

C05

Error in receiving serial

communication signal

Indoor or main outdoor unit is not operating correctly.

Mis-wiring of control wiring between indoor unit, main outdoor unit and

system controller.

CN1 is not connected properly.

C06

Activation of

protective

device

Protective device of sub

indoor unit in group control is

activated.

When using wireless remote controller or system controller, in order to

check the alarm message in detail, connect wired remote controller to

indoor unit temporarily.

P30

NOTE

1. Alarm messages in << >> do not affect other indoor unit operations.

2. Alarm messages in < > sometimes affect other indoor unit operations depending on the fault.

00_290811_2WAY_Eng.indb 57

2017/6/1 14:14:41

Remote control display

Alarm contents

E14

Two or more indoor units are set as main, in the group controlled indoor units.

E15

Fewer indoor units are found in Auto Addressing than the setting on outdoor PCB.

E16

More indoor units are found in Auto Addressing than the setting on outdoor PCB.

E18

No response from sub indoor to the main indoor unit in group control wiring.

E20

No indoor unit responded in Auto Addressing.

E31

Error in communication inside outdoor unit control box.

F01

Indoor unit heat exchanger liquid temperature sensor has failure. (E1)

F02

Indoor unit heat exchanger temperature sensor has failure. (E2)

F03

Indoor unit heat exchanger gas temperature sensor has failure. (E3)

F04

Compressor discharge temperature sensor has failure. (DISCH)

F06

Outdoor unit heat exchanger gas temperature sensor has failure. (EXG)

F07

Outdoor unit heat exchanger liquid temperature sensor has failure. (EXL)

F08

Outdoor temperature sensor has failure. (TO)

F10

Indoor suction air (room) temperature sensor has failure. (TA)

F11

Indoor discharge air temperature sensor has failure. (BL)

F12

Compressor inlet temperature sensor has failure. (SCT)

F14

Subcooling heat exchanger temperature sensor has failure. (SCG)

F16

High pressure sensor has failure. (HPS)

F17

Low pressure sensor has failure. (LPS)

F29

EEPROM on indoor unit PCB has failure.

F31

EEPROM on outdoor unit PCB has failure.

H01

Compressor primary current is overcurrent.

H02

PFC is overcurrent or VDC is overvoltage. (Single phase only)

H03

Compressor current sensor is disconnected or shorted.

H05

Compressor discharge temperature sensor is disconnected, shorted or misplaced. (DISCH)

H06

Low pressure sensor value is too low.

H31

Compressor HIC has failure. HIC is overcurrent or overheat. VDC is undervoltage or overvoltage.

L01

Indoor unit address setting has error. (No main indoor unit in group control.)

L02

Indoor unit model does not match with the outdoor unit model. (Multi-split/mini-split)

L03

Two or more indoor units are set as main in group control.

L04

Duplicate system address setting on outdoor units.

L05

Two or more indoor units are set as priority indoor unit (priority indoor unit).

L06

Two or more indoor units are set as priority indoor unit (non-priority indoor unit).

L07

Group control wiring is detected for indoor unit set as individual control.

L08

Indoor unit address is not set.

L09

Capacity setting of indoor unit is not correct.

L10

Capacity setting of outdoor unit is not correct.

L13

Indoor unit model does not match with outdoor unit.

L17

Model mismatch between outdoor units.

L18

4-way valve has failure.

P01

Thermal protector for Indoor unit fan motor is activated.

P03

Compressor discharge temperature is too high.

P04

High pressure swich is activated.

P05

AC power supply has abnormal.

P09

Connection to the panel of indoor unit is not good.

P10

Float switch of drain pan safety is activated.

P11

Drain pump failure or locked rotor.

P12

Indoor unit fan inverter protection control is activated.

P14

sensor has activated.

P16

Compressor secondary current is overcurrent.

P20

Too high load in refrigerant circuit.

P22

Outdoor unit fan motor has failure.

P29

Compressor start failure. Compressor is missing phase or reverse phase.

P31

Other indoor unit in group control has an alarm.

00_300268_2WAY_Eng.indb 59

2017/12/14 13:04:50

SM830258-01_欧州向け_1fan_mini_VRF.indb 19

18/02/14 8:59:53

Summary of Contents for S-22ML1E5
















































































































































































Search results

Summary of Contents for S-22ML1E5

Reviews:

Related manuals for S-22ML1E5

Brands by name

Popular brands

Panasonic S-22ML1E5, Service Manual & Test Run Service Manual

Search results

Summary of Contents for S-22ML1E5

Reviews:

Related manuals for S-22ML1E5

Brands by name

Popular brands