Panasonic PT-VW330U Operating Instructions Manual Download Page 62

Page: 62 / 82

- ENGLISH

Maintenance

Replacement

Before replacing the unit

When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect

the power plug from the wall outlet. (

pages 26, 30)

Be sure to observe the procedure “Turning off the projector” (

page 30) when performing power supply

operation.

Maintenance

Outer Case

Wipe off dirt and dust using a soft dry cloth.

If the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping. Dry off the projector

with a dry cloth.

Do not use benzene, thinner, or rubbing alcohol, other solvents, household cleaners, or chemical treated

dusters. Using them may cause deterioration of the outer case.

Front glass surface of the lens

Wipe off the dirt and dust off the front surface of the lens with soft clean cloth.

Do not use a cloth that has an abrasive surface or a cloth that is moist, oily, or covered with dust.

Do not use excessive force when wiping the lens as it is fragile.

Attention

The lens is made of glass. Impacts or excessive force when wiping may scratch its surface.

Please handle with care.

Air filters

Perform the maintenance of the air filter units in following cases. If a “Filter warning” icon appears on the screen,

replace the filters immediately.

The filter mesh is blocked, causing the filter warning icon appears on the screen and the <WARNING

Indicator> to light in red.

The filter mesh is blocked, causing the internal temperature to rise, the <POWER Indicator> to light, and the

power to shut off. (When the power is shut off, the <POWER Indicator> blinks in red and the <WARNING

Indicator> blinks faster than usual.)

Replacing the unit

Air filter units

Filter prevents dust from accumulating on the optical

elements inside the projector. Should the filter become

clogged with dust particles, it will reduce cooling fans’

effectiveness and may result in internal heat buildup

and adversely affect the life of the projector.

If a “Filter warning” icon appears on the screen,

replace the filters immediately.

Replacement of the air filter units

Remove the air filters.

1 )

Turn over the projector and pull out the filter

cover (bottom); pull up the handle and take out

the whole filter (bottom.)

Press up the latches and pull out the filter



Filter cover (side)

Latches (press up)

Handle (pull out)

Handle (pull up)

Filter cover (bottom)

Summary of Contents for PT-VW330U



















































































Search results

Summary of Contents for PT-VW330U

Reviews:

Related manuals for PT-VW330U

Brands by name

Popular brands

Panasonic PT-VW330U, Operating Instructions Manual

Search results

Summary of Contents for PT-VW330U

Reviews:

Related manuals for PT-VW330U

Brands by name

Popular brands