PT-
AT5000
E Full HD 3D Home Cinema Projector
Detail Clarity Processor 3 Gives Natural Clarity to
Even the Finest Details
This digital image processing circuit brings greater clarity and sharp-
ness to details embedded in the image. After analysing the video signal
frequency in each scene, the circuit optimises the sharpness of each
part of the image based on the extracted information. The resulting
images, 3D or 2D, have more natural, lifelike expression than those of
previous image-processing methods.
3D Viewing Monitor for Adjustment of Depth-of-Field
The projection size for
viewing 3D images can be
selected from among 9 dif-
ferent sizes, ranging from
40 inches to 200 inches
diagonally.*
4
The amount
of parallax is optimised
according to the projection
size, so comfortable, easy-
to-view 3D images can be enjoyed at any size. Furthermore, the 3D
Viewing Monitor makes sure the field of depth is within the comfortable
zone by a graphical representation and make adjustments accordingly.
3D Picture Balance with Waveform Monitor
The projector is able to
show the right and left
image side by side to
check if the two sides have
the same colours. The dif-
ference may occur due to
poor content quality. With
the Waveform Monitor dis-
played, you can adjust the
contrast, brightness, colour and tint as desired, and up to three adjust-
ment settings can be stored in memory for instant recall.
2D-3D Conversion
2D to 3D image conversion is possible, with five 3D effect modes to
select from.
Precisely Tuned 3D Projection with Optional Panasonic
VIERA 3D Eyewear
The PT-AT5000E uses frame sequential technology for 3D image pro-
jection. When viewing 3D content, signals from the PT-AT5000E’s built-
in infrared transmitter precisely control the left and right shutters of
the active 3D eyewear, which can be shared with VIERA 3D TVs.
Built-in 3D Infrared Transmitter
The PT-AT5000E comes equipped with a built-
in transmitter with maximum transmission
distance of six metres (about 20 feet).*
5
For
more range up to ten metres (about 33 feet),
an optional infrared transmitter, ET-TRM110 is
available for greater installation flexibility.
Abundant Connection Terminals
• HDMI™ with x.v.Colour™ and Deep Colour
The PT-AT5000E has three HDMI input terminals for digital trans-
mission without image degradation. The HDMI input terminals also
support Deep Colour and the x.v.Colour colour space. Deep Colour
provides 10-bit (over 1.07 billion) and 12-bit (over 68.7 billion) colour
depths for smooth gradation between colours, while x.v.Colour com-
pliance reproduces natural, lifelike images.*
6
• Programmable 12V Trigger for Automated Theatre Setup
Two 12V triggers are provided.*
7
Since the input and output can be
set independently (menu selectable), they can link flexibly with pow-
ered screens, room light
and powered curtains.
When combined with the
Intelligent Lens Memory,
they let you create a truly
classy home theatre.
VIERA Link for Easy Operation
The PT-AT5000E supports VIERA Link. If your home theatre
system contains VIERA Link-ready equipment, projection
can be started by using only the remote control unit of the
PT-AT5000E, regardless of whether the source is a Blu-ray Disc or a
TV program stored on an HD recorder. This eliminates the need for
hassling with several remote controls.*
8
Up to 5,000-Hour Lamp Replacement Cycle
*
9
and
Simple Maintenance
Panasonic’s proprietary lamp drive system helps maintain lamp per-
formance, resulting in a up to 5,000-hour lamp replacement cycle. For
easy maintenance, you can replace the filter from the side and the
lamp from the top of the projector. The dust filter and lamp are easily
replaced even after the PT-AT5000E is installed on the ceiling.
Conventional sharpness control:
Sharpness is applied uniformly, which
can cause a halo or ring effect.
Detail Clarity Processor 3: Signal
frequency is extracted realtime and
necessary sharpness is applied at varying
degrees for natural, lifelike images.
Built-in 3D infrared
transmitter
Ecology-conscious Design
Panasonic works from every angle to minimize environmental impact in the
product design, production and delivery processes, and in the performance of
the product during its life cycle. The PT-AT5000E reflects the following eco-
logical considerations.
•
No halogenated flame retardants are used in the cabinet.
•
Lead-free glass for the lens.
•
Standby power consumption of only 0.08 W has been achieved.
•
A sleep-timer that reduces wasteful power consumption.
•
RoHS compliant.
*4
Projection size for 2D images covers from 40 inches to 300 inches diagonally.
*5
The indicated distance between the projector and screen is valid when the conditions
described below are satisfied. Also, note that the transmission distance can differ largely due to strong light, such as sunlight and fluorescent lamps, at the installation
location or due to the screen type or material.
C
ONDITION
1
: The distance between the screen and the 3D Eyewear (viewing position) is 5 metres to the front of the screen.
C
ONDITION
2
: The screen is 100 inches, measured diagonally, and has a screen gain of 1.
C
ONDITION
3
: The projector is set up in front of the screen, and the lens shift function is
not used.
C
ONDITION
4
: The [3D IR TRANSMITTER] setting in the main unit is set to [STRONG].
*6
Effective in Rec. 709 image mode.
*7
The trigger terminals also operate as
the 3D shutter outputs to connect the optional 3D IR transmitter ET-TRM110.
*8
Cannot be used simultaneously with TV that supports VIERA Link. Some operations may not
be available depending on the equipment. In this case, use its own remote control to operate the equipment.
*9
When a lamp power is set to ECO. The lamp replacement
cycle is up to 4,000 hours when the lamp mode is set to NORMAL. The values above are maximum values when they are used in cycles of being turned on for 2 hours and off
for 0.25 hours. When the lamps are turned on and off more frequently, the lamp replacement cycle is shortened. The usage environment affects the lamp replacement cycle.
