background image

MODEL:   Miniature Camera

PCF2, PCV2, PCF6, PCV6,

PCF6W, PCV6W

PRODUCT INSTRUCTIONS

STANDARD INSTALLATION PROCEDURE

CONTENTS INCLUDE:

     

(1) Dome base

     (1) Dome

     (1) Dome liner

     (1) Camera swivel plate

     (1) Camera mount with camera, lens, and PC Board

     (1) Camera adjustment arm

     (1) Camera adjustment template

     (2) 4-40 x 1/4" screws

     (1) 8-32 x 3/8" screw

INSTALLATION
1

. Locate the area on the ceiling or wall where the housing is

to be mounted.  Cut a hole no larger than 2 1/4" in diam-
eter and feed the necessary wires/cable through the hole.

2

. Remove the dome and liner by turning the dome counter-

clockwise and gently pulling down.

3

. Place the dome base against the ceiling/wall, with the

cutout in the center, and mark the keyhole slots.  Insert a
screw on each mark and tighten down 3/4 of the length
of the screw.

4.

 Feed the wires/cable through the hole in the dome base.

5. 

Place the keyhole slots in the base over the screws and

slide forwared so that the screws hold the base to the sur-
face.  Tighten the screws.

Dome Tab Slots

Key Hole Slots

Wire or Cable Entry

ATTACHING HOUSING (PCF6/PCV6 PENDANT MOUNT)
1.

 Install 3/4" EMT pipe (not provided) to the desired length.

2. 

Slide the top dome 10" to 12" onto the pipe, leaving enough

room to work.  Run the wiring through the EMT connector
and wiring hole inside the top of the housing.

3.

  Slide complete unit onto the pipe.  Tighten the set screw

when

    in place.

4.

 Once the housing is secured to the pipe, slide the top dome

down onto the top of the housing.

3/4" EMT Pipe
(not provided)

Top Dome

Housing

Dome

Liner

Manufactured by:

for

Before attempting to connect or operate this product, please read these instructions completely.

81-IN3047-9922

EMT Clamp
Connector

 

Connect Class 2 power supply only!

!

NOTE:

  Once the housing has been attached to the desired

            location, connect the power and video wires as
            required.

DESCRIPTION

:     Dome Housing, Color Camera - PCF2, PCV2

Pendant Mount Dome Housing, Color Camera - PCF6, PCV6
Wall Mount Dome Housing, Color Camera - PCF6W, PCV6W

Wire or Cable Entry

Dome Tab Slots

Key Hole
Slots

Summary of Contents for PCF2






Reviews: