Panasonic OmniVision PV-M1347 Service Manual Download Page 122

Page: 122 / 143

7-1

REPLACEMENT PARTS LISTS

BEFORE REPLACING PARTS,
READ THE FOLLOWING:

1. Use only original replacement parts:

To maintain original function and reliability of repaired
units, use only original replacement parts which are
listed with their part numbers in the parts list.

2. IMPORTANT SAFETY NOTICE

Components identified by the sign

have special

characteristics important for safety. When replacing any
of these components, use only the specified parts.

3. SPECIAL NOTE

All integrated circuits and many other semiconductor
devices are electrostatically sensitive and therefore
require the special handling techniques described under
the "ELECTROSTATICALLY SENSITIVE (ES) DE-
VICES" section of this service manual.

4. Parts with no Ref. No. in "EXPLODED VIEW" are not

supplied. And some Ref. No. will be skipped. Be sure to
make your orders of replacement parts according to the
parts list.

5. Parts different in shape or size may be used. However,

only interchangeable parts will be supplied as service
replacement parts.

6. The parts which "AKEI" is indicated in Remarks column

will be supplied from AKEI factory.

Mechanical Replacement Notes

1. Section No. of parts shown in Exploded Views are

indicated in the Remarks column.

2. Capstan Rotor Unit, Capstan Holder Unit, and Stopper

are supplied as Capstan Rotor Kit (Ref No. 51) only.

3. Capstan Stator Unit, Capstan Rotor Unit, Capstan

Holder Unit, and Stopper are supplied as a Capstan
Stator Kit (Ref No. 52) only. However, IC2501
(AN3845SC) is available separately as a replacement
part. When installing the IC2501 or Capstan Stator unit,
be sure to apply Silicon Grease (VFK1301). Refer to
"Capstan Stator Unit" of "DISASSEMBLY/ASSEMBLY
PROCEDURES OF MECHANISM" section.

4. Since the UHF/VHF TUNER/TV DEMODULATOR UNIT

(Ref No. E21) has already been pre-adjusted at the
factory, do not try to adjust the UHF/VHF TUNER/TV
DEMODULATOR UNIT. The UHF/VHF TUNER/TV
DEMODULATOR UNIT replacement part is available as
a complete assembly unit only.

5. The Infrared Remote Control Unit (Ref No. 123) replace-

ment part is available as a complete assembly unit only.
Do not try to disassemble the Infrared Remote Control
Unit. However, the battery cover is available separately
as a replacement part.

6. Cut Washers (Ref No. 416 and 417) are not reusable.

If removed, install a new one.

7. Main Cam Push Nut (Ref No. 414) is not reusable.

If removed, install a new one.

Electrical Replacement Notes

1. Item numbers with capital letter E (Example: E1, E2,…)

in the Ref. No. column are shown in the exploded views.
The E item numbers are also printed on the same page
at the top of the column.

2. The parts with "

" mark are supplied individually or as a

unit. The parts with "

" mark are supplied individually or

as a unit, and are included in "

" parts listed directly

above in the parts list.

3. Unless otherwise specified;

All resistors are in ohms, 1/4W, +/-5%, carbon,
K = 1,000 ohm, M = 1,000 kohm.
All capacitors are in microfarads, P = micromicrofarad,
+/-10%.
All coils are in microhenries, M = 1,000 microhenry,
+/-10%.

4. Abbreviation

RTL: Retention Time Limited

This indicates that the retention time is limited for
this item. After the discontinuation of this item in
production, it will no longer be available.

NR: Non Repairable Board Ass'y
MGF CHIP: Metal Glaze Film Chip
C CHIP: Ceramic Chip
COMPLX CMP: Complex Component
W FLMPRF: Wirewound Flameproof
C.B.A.: Circuit Board Assembly
P.C.B.: Printed Circuit Board
E.S.D.: Electrostatically Sensitive Devices

5. SERVICE OF CHIP PARTS

When servicing chip parts, please use a soldering iron of
less than 30 watts. Refer to "IC, TRANSISTOR AND
CHIP PART INFORMATION" page.

6. The parts with "

" are 0 ohm resistor. When replacing,

a wire can be substituted for a 0 ohm resistor.

7. IC6001 replacement note:

products

replacement parts

MN675058A5P2
MN675058A5P1
MN675058A5P

MN675058A5P2

COMPARISON CHART OF MODELS & MARKS

MODEL