100
Indications
1:
The Time Code becomes inaccurate.
1:
The Time Code Indication counter may not be constant
in the reverse direction in Slow Motion Playback Mode,
but this is not a malfunction.
2:
The Remaining Tape Time Indication disappears.
2:
When you record still pictures in Photoshot Mode, the
Remaining Tape Time Indication may disappear
temporarily. However, it reappears when recording
normally.
3:
The Remaining Tape Time Indication does not
match the actual remaining tape time.
3-1: If scenes of less than 15 seconds are continuously
recorded, the remaining tape time cannot be displayed
correctly.
3-2: In some cases, the Remaining Tape Time Indication
may show remaining tape time that is 2 to 3 minutes
shorter than the actual remaining tape time.
Playback (Pictures)
1:
Pictures cannot be played back even when the [
1
]
Button is pressed.
1:
Is the [VCR] Lamp on? If the [VCR] Lamp is not on, the
playback function cannot be used.
(
l
76)
2:
Mosaic-pattern noise appears on images during
Cue, Review or Slow Motion Playback.
2:
This phenomenon is characteristic of digital video
systems. It is not a malfunction.
3:
Although the Movie Camera is correctly connected
to a TV, playback images cannot be seen.
3:
Have you selected “Video Input” on the TV? Please
read the operating instructions of your TV and select the
channel that matches the input sockets used for the
connection.
4:
Playback picture is not clear.
4:
Are the heads of the Movie Camera dirty? If the heads
are dirty, playback image cannot be clear.
(
l
97)
Playback (Sound)
1:
Sound is not played back from the built-in speaker
of the Movie Camera or the headphones.
1:
Is the volume too low? During playback, keep pressing
the [PUSH] Dial until the [VOLUME] Indication appears.
Then, turn the [PUSH] Dial to adjust the volume.
(
l
76)
2:
Different sounds are reproduced at the same time.
2:
[12bit AUDIO] on the [PLAYBACK FUNCTIONS]
Sub-Menu of the [VCR FUNCTIONS] Main-Menu has
been set to [MIX]. As a result, the original sound and
sound that was recorded by audio dubbing are played
back together. It is possible to reproduce the sounds
separately.
(
l
80)
3:
The original sound was erased when audio dubbing
was performed.
3:
If you perform audio dubbing on a recording done in
[16bit] Mode, the original sound will be erased. If you
wish to preserve the original sound, be sure to select
[12bit] Mode at the time of recording.
4:
Sounds cannot be played back.
4-1: Although a Cassette with no audio dubbing is being
played, is [12bit AUDIO] on the
[PLAYBACK FUNCTIONS] Sub-Menu of the
[VCR FUNCTIONS] Main-Menu set to [ST2]? To play
back a Cassette with no audio dubbing, [12bit AUDIO]
must be set to [ST1].
(
l
80)
4-2: Is the Variable Speed Search Function working? Press
the [
1
] Button to cancel the Variable Speed Search
Function.
(
l
76)
Card
1:
Recorded pictures are not clear.
1:
Is [PICTURE QUALITY] on the [CARD SETUP]
Sub-Menu set to [NORMAL] or [ECONOMY]? If
recording is done with it set to [NORMAL] or
[ECONOMY], images with fine details may include a
mosaic-like pattern. Set [PICTURE QUALITY] to [FINE].
(
l
84)
2:
Card Photoshot Playback images do not look
normal.
2:
The picture may be damaged. In order to prevent the
loss of image data, backing up on a Cassette or a
personal computer is recommended.
(
l
83, 85, 95)
3:
During Playback the [
t
] Indication is displayed.
3:
The image was either recorded in a different format, or
data is damaged.
4:
Even if a Card is formatted, it cannot be used.
4:
Either the Movie Camera or the Card may be damaged.
Please consult a dealer.
~~~~~~~~~~~~~~~~~~~
CE.book 100 ページ ２００１年８月６日 月曜日 午後４時２２分
Summary of Contents for NV-DS88EN
Page 53: ...103 ...
