Panasonic NN-SG158S, Installation Instructions Manual

Page: 21 / 26

INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C4.
C5. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•
Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
Installation Instructions
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts. 4
3
ATTACH THE MOUNTING
PLATE TO THE WALL C1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
3 ⁄
4
″ (19 mm) onto
each bolt.
1
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
RECIRCULATING
(Non-Vented Ductless)
C
Install or change Charcoal Filter
C3. Check Blower Plate
NOTE:
Cabinet Cabinet
If the cabinet depth including the cabinet doors
is more than 13""'' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/intake.
o
EN-20
12"
4"
NOTE: IT IS VERY IMPO RTANT TO
READ AND FOLLOW TH E DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE .
This Rear Wall Template se
rves to position the bottom
mounting plate and to locat e the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately. 2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at leas t one wood
screw mounted firmly in a s tud to support the weight
of the microwave. Mark two
additional, evenly spaced
locations for the supplied to
ggle bolts.
3. Drill holes in the marked l ocations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stu
d, drill 5/8" holes for
toggle bolts. DO NOT INSTALL THE MO UNTING PLATE
AT THIS TIME.
4. Remove the template fro m the rear wall.
5. Review the Installation In struction book for your
installation situation.
Locate and mark holes to
align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
OF
THE CENTERLINE.
MARK THE LOCATION F OR 2 ADDITIONAL, EVE NLY
SPACED TOGGLE BOL
TS IN THE MOUNTING PLATE
AREA. Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION F
OR 2 ADDITIONAL, EVE
NLY
SPACED TOGGLE BOL TS IN THE MOUNTING PL
ATE
AREA.
Trim the rear wall templa
te along the dotted line.
Darle vuelta a la hoja para
consultar la
versión en Español.
3/8" TO EDGE
Trim the rear wall templa
te along the dotted line.