Panasonic NN-SG158S, Installation Instructions Manual

Page: 17 / 26

INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
been properly routed and secured,
and that the wires are not pinched.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Back of
Microwave
Installation Instructions
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
B1.
You need to cut an opening in the rear wall for
outside exhaust.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
B2.
OUTSIDE BACK EXHAUST
(Horizontal Duct)
B
Blower Plate
REMOVE BLOWER PLATE
B2. Remove Blower Plate
3/8" TO EDGE


 














NOTE: IT IS VE
RY IMPOR
TANT TO
READ AND
FOLLOW TH
E DIRECTIONS
IN THE IN
STALLATIO
N INSTRUCTIO
NS
BEFORE PR
OCEEDING
WITH THIS
REAR WALL
TEMPLATE
. This Rear Wall
Template serv
es to position
the bottom
mounting plate a
nd to locate the
horizontal exhaust
outlet.
1. Use a level
to check that th
e template is posi
tioned
accurat
ely. 2. Locate and
mark at least one
stud on the lef
t or
right side
of the centerline. 
It is important
to use at leas
t one wood
screw mounted
firmly in a stud
to support the
weight
of the microw
ave. Mark two
additional, evenly
spaced
locations for the
supplied toggle
bolts.
3. Drill holes
in the marked
locations. Wh
ere there is
a stud, drill a
3/16" hole for wood
screws. For hol
es
that do not li
ne up with a stu
d, drill 5/8" hole
s for
toggle bolts.
 DO NOT INSTALL
THE MOUNT
ING PLATE
AT THIS TIME.
4. Remove the
template from
the rear wall.
5. Review
the Installation
Instruction boo
k for your
installation sit
uation.
Locate and
mark holes to
align with ho
les in the
mounting p
late. IMPORTANT:
LOCATE
AT LEAST ON
E STUD ON EITH
ER SIDE OF
THE CENTER
LINE. MARK TH
E LOCATION FOR
2 ADDITIONAL
, EVENLY
SPACED TOGG
LE BOLTS IN
THE MOU
NTING PLA
TE
AREA.
Locate and
mark holes to
align with h
oles in the
mounting plate
. IMPORTA
NT:
LOCATE
AT LEAST ON
E STUD ON EIT
HER SIDE
OF
THE CENTER
LINE. MARK TH
E LOCAT
ION FOR
2 ADDITIONAL
, EVENLY
SPACED TOGG
LE BOLTS
IN THE MOU
NTING PLA
TE
AREA.
Trim the rear wa
ll template a
long the d
otted line.
Trim the rear wall
template along
the dotted
line.













12"
4"
Darle vuelta a la
hoja para consul
tar la
versión en Españ
ol.
Make sure the motor wiring has
12"
4"
NOTE: IT IS VERY I
MPORTANT TO
READ AND FOLLO W THE DIRECTION
S
IN THE INSTALLAT
ION INSTRUCTION S
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLA
TE.
This Rear Wall Templ
ate serves to position th e bottom
mounting plate and to l
ocate the horizontal e xhaust
outlet.
1. Use a level to chec
k that the template is p
ositioned
accurately.
2. Locate and mark at lea
st one stud on the left o
r
right side of the cen
terline.
016' It is important to use a
t least one wood
screw mounted firmly i n a stud to support the w
eight
of the microwave. Mar k two additional, even
ly spaced
locations for the suppl
ied toggle bolts.
3. Drill holes in the mar
ked locations. Where t here is
a stud, drill a 3/16" h
ole for wood screws. F or holes
that do not line up w ith a stud, drill 5/8" ho
les for
toggle bolts.
016' DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the templa te from the rear wall.
5. Review the Installati on Instruction book for
your
installation situation .
Locate and mark holes
to align with holes in t he
mounting plate.
IMPORTANT:
LOCATE AT LEAST
ONE STUD ON EIT
HER SIDE OF
THE CENTERLINE.
MARK THE LOCATIO
N FOR 2 ADDITION AL, EVENLY
SPACED TOGGLE BO
LTS IN THE MOUN
TING PLATE
AREA.
Trim the rear wall tem
plate along the dott ed line.
Darle vuelta a la hoja
para consultar la
versión en Español.
Locate and mark holes to align with holes in t
he
mounting plate.
IMPORTANT:
LOCATE AT LEAST O
NE STUD ON EITHER SI
DE OF
THE CENTERLINE.
MARK THE LOCATIO
N FOR 2 ADDITION AL, EVENLY
SPACED TOGGLE BO
LTS IN THE MOUN TING PLATE
AREA.
Trim the rear wall t
emplate along the dotted lin
e. 3/8" TO EDGE
EN-16