13
English
Select the language
Select your country
Select [Home]
Select [Home] for use in a home viewing environment.
≥
[Shop] is for shop display.
≥
To change the viewing environment later on, the set
will need to have all settings initialised by accessing
[Shipping Condition].
Set up the network connection
Tick the TV signal mode to tune, and then select
[Start Auto Tuning]
≥
If you use an RF selector, switch it to the digital TV
signal before starting the Auto Tuning. As soon as the
digital TV scan is finished, switch it to the analogue TV
signal to tune analogue channels. Even if some
channels are not tuned correctly, you can try to tune
them by [Auto Tuning] in the [Setup] menu.
Select your region (Digital TV)
Enter your postcode
∫
When you select the analogue TV signal, select
your area.
≥
When selecting [CATV/Other], press the OK button,
and then select the Channel Plan from Indian CATV,
South Africa, American System, American CATV or
Japan CATV.
If tuning has failed check the RF cable, and the network
connection, and then follow the on-screen instructions.
<Note>
≥
The TV goes into Standby mode when no signal is
received and no operation is performed for 10 minutes
if [No signal Power off] in the Timer menu is set to [On]
(factory setting).
≥
To retune all channels
[Auto Tuning] in [Tuning Menu] ([Setup] menu)
≥
To add the available TV signal mode later
[Add TV Signal] in [Tuning Menu] ([Setup]
menu)
≥
To initialise all settings
[Shipping Condition] in [System Menu] ([Setup]
menu)
FAQs
Before requesting service or assistance, please follow
these simple guides to solve the problem.
≥
For details, refer to [eHELP] (Support > FAQs).
It takes several seconds to display the image after
turning the TV on
≥
When turning the TV on, the panel adjustment is
performed. It is not a malfunction.
The TV does not switch on
≥
Check the mains lead is plugged into the TV and the
mains socket.
The TV goes into Standby mode
≥
Auto power standby function is activated.
The remote control does not work or is intermittent
≥
Are the batteries installed correctly?
≥
Has the TV been switched on?
≥
The batteries may be running low. Replace them with
new ones.
≥
Point the remote control directly at the TV’s remote
control signal receiver (within about 7 m and a
30 degree angle of the signal receiver).
*
≥
Situate the TV away from sunshine or other sources of
bright light so they do not shine on the TV’s remote
control signal receiver.
*
≥
If you are trying to use voice controls, is the remote
control registered (paired) with the TV?
(p. 10)
≥
If the solutions above do not fix the problem,
deregister (unpair) the remote control, then
register (pair) it again.
“When the remote
control does not respond” (p. 10)
When infrared communication is used
No image is displayed
≥
Check the TV is turned on.
≥
Check the mains lead is plugged into the TV and the
mains socket.
≥
Check the correct input mode is selected.
≥
Is [Luminance Level], [Contrast], [Brightness] or
[Colour] in the Picture menu set to the minimum?
≥
Check all required cables and connections are firmly
in place.
≥
Press and hold the Power On / Off switch on the TV
for 5 or more seconds and then release your finger to
reboot the TV.
An unusual image is displayed
≥
This TV has a built-in Self Test. Makes a diagnosis of
picture or sound problems.
[TV Self Test] ([Help] menu)
Auto Tuning is now complete and the TV is
ready for viewing.
Malaysia
Indonesia
TH-55_65MZ1000GK_Eng_TQB4GA0246.book 13 ページ ２０２３年３月２７日 月曜日 午後３時３３分
