19
Indicator for replacing the dust bag
Turn the power control to the highest setting and lift the
nozzle off the
fl
oor. If the dust indicator turns red, the dust
bag is full and requires replace the dust bag.
NOTE:
If the dust bag is not properly installed, the cover will
not close. Be sure to check that the bag is properly
installed before operating, otherwise dust will leak
out. The dust bag can easily lay on the dust cover
packing or clip between bag collar and body, so be
sure to properly extend it into the vacuum cleaner
body.
Replacing the dust bag
D-1
Lift dust cover catch and raise dust cover until it
clicks properly.
D-2
Remove bag collar from bag holder and pull out
dust bag.
D-3
Set a new dust bag.
D-4
Close dust cover properly until you hear it click.
Turbine nozzle
D-5
After removing the brush cover with a coin, remove
the beater bar from the belt.
Then cut across threads, strings, hairs, etc. from the
beater bar with a pair of scissors. (Removal as per
reverse procedure)
NOTE:
Take care not to cut the brush.
Do not wash in water.
Vacuum cleaner body
D-6
Wipe with a soft cloth soaked with water.
Maintaining the Pre-motor Filter
Follow the procedure written below when the suction power
is not restored after replacing a new bag.
D-7
Open the dust cover.
D-8
Remove the pre-motor
fi
lter.
D-9
Wash gently with water and then allow to dry in a
shaded location.
D-10
Replace to its original location.
NOTE:
Make sure you remember to replace the
fi
lter. If the
fi
lter is not installed, it will cause motor failure.
• Do not wash the
fi
lter in a washing machine or dry it with a
dryer or other source of hot air.
CAUTIONS
• The plug must be removed from the socket-outlet
before cleaning or maintaining the appliance.
• To avoid injury, keep your
fi
ngers and hands away
from the beater bar.
• DO NOT use hot air or hot surface to dry
fi
lters. Keep
at room temperature for approximately 24 hours.
• IMPORTANT: Before re-installing the washable
fi
lters,
make sure they are completely dry to avoid damaging
the cleaner.
Filter care
D-11
Exhaust
fi
lter
Exhaust
fi
lter is installed in the rear side of the
vacuum cleaner. This
fi
lter retains any small dust
particles which may be present in the expelled air.
It is advisable to change the
fi
lter once or twice a
year, depending on use. To change the
fi
lter, hold
the exhaust cover (as illustrated) and pull it out. After
changed the
fi
lter, set the exhaust cover to its position
(as illustrated).
NOTE:
IMPORTANT:
Never use the cleaner without the correct
fi
lters properly installed. Failure to do so may
result in damage to the motor.
What to do if your cleaner does not work
Check that the appliance is correctly plugged in and that the
electrical socket is working. In case that the thermal cut-out
device has operated, wait until it resets after approximately
60 minutes. If after having checked the mentioned points, the
cleaner does not work, take it to an Authorized Service Centre to
be repaired.
What to do when the suction performance
reduces
• Stop the cleaner and unplug from the socket.
• Check whether the wands, hose and accessories are blocked or
not. If they are blocked, remove the obstruction.
• Check that the dust bag is full. If it is full, replace it to a new
one.
• Check that Pre-motor Filter or Exhaust Filter is blocked with
dust. If they are blocked, clean them out or replace.
SPECIFICATIONS
MC-CG476, MC-CG475
Power source
230 V~50 Hz
Max. Input
2500 W
Nominal input
2100 W
Dimensions
(W x L x H)
280 mm x 425 mm x 260 mm
Net weight
5.3 k
g
Extension wands
Telescopic
Crevice nozzle
√
Dusting brush
√
REMINDER FOR CUSTOMER
The model and serial number of this product may be found on the
nameplate located at the underside of your cleaner. You should
note the model and serial number in the spaces provided and
retain this book as a permanent record of your purchase.
Model Number. .............................................................................
Serial No. ......................................................................................
Date Purchased. ...........................................................................
Where Purchased. ........................................................................
D - MAINTENANCE AND SERVICING
