Panasonic M16eG Installation Manual Download

Page: 12 / 18

Port LED

Left

Right

Port LED (Left)

Port LED (Right)

Display mode

STATUS/ECO

Behavior

Description

Green Light

Link is established.

Green Blink

Transmitting and receiving data.

Off

No device connected.

Table1. Ports and Port LED lamps 1 to 16 correspond as shown below.

GIGA

Green Light

Link is established at 1000 Mbps.

Off

Link is established at 100 Mbps or
10 Mbps, or no device is connected.

100M

Green Light

Link is established at 100 Mbps.

Off

Link is established at 1000 Mbps or
10 Mbps, or no device is connected.

FULL

Green Light

Link is established at full-duplex.

Off

Link is established at half-duplex or
no device is connected.

Orange Light

Shutting down by loop detection.

Off

Not shutting down by loop
detection.

LOOP HISTORY

Green Light

Loop has been detected within the
last 3 days.

Off

No loop detection history.

Part Names and Functions

SFP

▲

SFP

▼

RIGHT LED(ORANGE):LOOP DETECTION

Summary of Contents for M16eG



















Search results

Summary of Contents for M16eG

Reviews:

Related manuals for M16eG

Brands by name

Popular brands

Panasonic M16eG, Installation Manual

Search results

Summary of Contents for M16eG

Reviews:

Related manuals for M16eG

Brands by name

Popular brands