manualshive.com logo in svg

Panasonic LUMIX DMC-FX9GC, Operating Instructions Manual

Share
Download
Panasonic LUMIX DMC-FX9GC Operating Instructions Manual Download Page 12

Preparation

12

VQT0S68

Charging the Battery with the Charger

When the camera is shipped, the battery is 
not charged. Charge the battery before 
use.

1

Attach the battery with attention 
to the direction of the battery.

2

Connect the AC cable.

• The AC cable does not fit entirely into 

the AC input terminal. A gap will remain 
as shown below.

• When the [CHARGE] indicator 

A 

lights 

in green, charging starts.

• When the [CHARGE] indicator 

A 

turns 

off (in about 130 minutes), charging is 
completed.

3

Detach the battery after charging 
is completed.

• After charging is completed, be sure to 

disconnect the AC cable from the 
electrical outlet.

• The battery becomes warm after use/

charge or during charge. The camera also 
becomes warm during use. However, it is 
not a malfunction.

• The battery is exhausted when it is left for 

a long period of time after being charged. 
Recharge the battery when it is 
exhausted.

• Use the dedicated charger and battery.
• Charge the battery with the charger 

indoors.

• Do not disassemble or modify the 

charger.

Summary of Contents for LUMIX DMC-FX9GC

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands