manualshive.com logo in svg

Panasonic KX-WT125, Operating Instructions Manual, Page: 69 / 84

Share
Download
Panasonic KX-WT125 Operating Instructions Manual Download Page 69

Troubleshooting and Error Messages

69

Problem

Possible Cause

Solution

The handset 
stops working 
during operation.

Re-insert the batteries and 

try again.
(See "Battery Installation" on 
page 5.)

You cannot use 
the handset 
during a power 
failure.

The handset will not 
function during a power 
failure because the PBX 
stops emitting radiowaves.

The headset 
does not work.

A headset tone cannot be 
heard when receiving an 
incoming call when the 
headset is attached.

• 

Make sure the headset 
ringer setting is set to 
"

On

". (See "Incoming 

Option" on page 59.)

• 

Make sure the headset 
jack is connected 
properly. (See "Location of 
Controls" on page 8.)

Noise is 
frequently heard.

• 

Place the handset and CS 
away from other electrical 
appliances.

• 

Move closer to the CS.

Two short beeps 
are heard during 
a conversation.

The radio signal is weak.

Move closer to the CS.

You charged 
the batteries 
for 7 hours, but 
the beep tones 
sound, and 

 

flashes (needs to 

be charged) after 
a few telephone 
calls.

The battery charge 
contacts may be dirty.

Clean the battery charge 
contacts without damaging 
them and charge once more.

It is time to change the 
batteries.

Replace with new batteries.

While charging 
the batteries, the 
handset and the 
AC adaptor feel 
warm.

These are normal 
conditions.

Summary of Contents for KX-WT125





















































































Reviews:

No comments