background image

Problem

You press 

(POWER)

to

power the unit ON, but
the unit does not work.

Your message cannot
be transmitted.

The other party’s
message cannot be
received.

Other conversations or
noise on a channel is
heard when receiving.

Problem

Limited Talk Range

Static, sound cuts
in/out, fades.
Interference emits
when transmitting.

You cannot change
channel/code settings.

Previously
programmed items are
erased.

” flashes on the

display.

The display is dim.

If you cannot solve
your problem

–13–

8

Things You should Know

¤

8-B Before Requesting Help

Remedy

Reposition or replace batteries (1-C).

Make sure 

(TALK)

is completely

pressed as you transmit.

Reposition or replace batteries (1-C).

Make sure the other party’s channel/
code settings are the same as yours.

Make sure 

(TALK)

is not inadvertently

being pressed.

Reposition or replace batteries (1-C).

Obstructions, operating indoors or in
vehicles, may interfere with
communication. Change your location
and try again.

Make sure the volume is not OFF 
(3-B).

Hold the unit near your ear to hear the
message from the sub speaker when
the flip is open.

Confirm the group code setting (2-B).
If the setting is “0” (OFF), reprogram
the same group code as the other
party, and try again.

Shared channel or group code may
be in use. Try another.

Remedy

Steel/concrete structures, heavy
foliage and use in buildings or
vehicles will decrease range. Check
for clear line of sight to improve
transmission.

Wearing the unit on your body, such
as in a pocket or on a belt, will
decrease range. Change location of
the unit.

You are too close to the other party.
You should be at least 5 feet apart.
Increase your distance.

You are too far from the other party.
Obstacles interfere with transmission.
Talk range is up to 2 miles in clear,
unobstructed conditions.

Make sure the unit is unlocked (6-B).

When the batteries have been
replaced, your programmed items will
be erased. Reprogram them again if
necessary.

Reposition or replace batteries (1-C).

Reposition or replace batteries (1-C).

Call our customer call center at
1-800-211-PANA(7262).

Summary of Contents for KX-TR325B

















Reviews: