Panasonic KX-TG1843ALS Service Manual Download Page 30

Page: 30 / 93

8.2.

The Setting Method of JIG (Base Unit)

8.2.1.

Preparation

8.2.1.1.

Equipment Required

•

DECT tester: Rohde & Schwarz, CMD 60 is recommended.

•

Frequency counter: it must be precise to be able to measure 1Hz (precision; ±4ppm).

Hewlett Packard, 53131A is recommended.

•

Digital multi-meter (DMM): it must be able to measure voltage and current.

•

Oscilloscope

8.2.1.2.

JIG and PC

•

EEPROM serial JIG

JIG Cable: PQZZ1CD300E*

•

PC which runs in DOS mode

•

Batch file CD-ROM

for setting: PQZZTG1840AL

Note:

*: If you have the JIG Cable for TCD500 series (PQZZ1CD505E), change the following values of resistance. Then you can use
it as a JIG Cable for both TCD300 and TCD500 series. (It is an upper compatible JIG Cable.)

Resistor

Old value (k

Ω

)

New value (k

Ω

)

3.3

4.7

8.2.2.

PC Setting

8.2.2.1.

Connections

1. Connect the AC adaptor to CN2 (base unit).

2. Connect the JIG Cable GND (black).

3. Connect the JIG Cable URX (red) and UTX (yellow).

Note:

*: COM port names may vary depending on what your PC calls it.

KX-TG1843ALS / KX-TGA122AZS / KX-TGA121AZS

Summary of Contents for KX-TG1843ALS






























































































Search results

Summary of Contents for KX-TG1843ALS

Reviews:

Related manuals for KX-TG1843ALS

Brands by name

Popular brands

Panasonic KX-TG1843ALS, Service Manual

Search results

Summary of Contents for KX-TG1843ALS

Reviews:

Related manuals for KX-TG1843ALS

Brands by name

Popular brands