Panasonic KX-TG1843ALS Service Manual Download Page 10

Page: 10 / 93

4.4.

Guide to Settings

For your reference, a chart of all items which can be customised for the base unit and the handset is printed below.

•

When customising the base unit and the handset, the current item or setting is indicated by

4.4.1.

Base Unit Settings

•

These items are customised using the handset.

Note:

•

Up to 3 menu items can be displayed at a time. To select a menu item not shown on the current page, scroll up or down
by pressing the navigator key,

, respectively.

4.4.2.

SMS Settings

Note:

•

Ifthe base unit is reset to its default settings, the contents ofthe receive and send lists will be erased.

4.4.3.

Answering System Settings

KX-TG1843ALS / KX-TGA122AZS / KX-TGA121AZS

Summary of Contents for KX-TG1843ALS






























































































Search results

Summary of Contents for KX-TG1843ALS

Reviews:

Related manuals for KX-TG1843ALS

Brands by name

Popular brands

Panasonic KX-TG1843ALS, Service Manual

Search results

Summary of Contents for KX-TG1843ALS

Reviews:

Related manuals for KX-TG1843ALS

Brands by name

Popular brands