manualshive.com logo in svg

Panasonic KX-TDA0480, Installation Manual, Page: 97 / 174

Share
Download
Panasonic KX-TDA0480 Installation Manual Download Page 97

Logical Installation

Installation Manual

97

Trunk Priority Folder

Use the Trunk Priority section of the Worksheet to define the order (priority) in which alternate 
trunk routes will be selected in the event that the first Trunk Group accessed is busy.

Priority 1 will be the first group searched. If the destination number is not found on the 
associated Trunk Group, then the remaining group is searched in priority order.

Up to 2 Hunt Patterns can be defined for each unit.

The Hunt Pattern list provides records for each Hunt Pattern that was defined in the Hunt 
Patterns folder. To configure a Hunt Pattern, select the desired pattern in the Hunt Pattern list 
and complete the fields located beneath the Hunt Pattern list.

The Hunt Pattern list is updated as new values are configured in the fields.

Priority

Use the pull-down list to select a Priority setting (1 or 2).

Summary of Contents for KX-TDA0480















































































































































































Reviews:

No comments