manualshive.com logo in svg

Panasonic KX-TDA0480, Installation Manual, Page: 100 / 174

Share
Download
Panasonic KX-TDA0480 Installation Manual Download Page 100

Logical Installation

100

Installation Manual

Select Protocol

Use the pull-down list to choose a protocol for the selected port (H.323).
This setting affects only the method in which voice data is handled by the unit and has no effect 
upon the selection of a network H.323 Gatekeeper or DNS facilities.

Packet send interval

Use the Efficiency slide bar to adjust the packet size to bandwidth ratio for the selected port.

To operate the 

Packet send interval

 slide bar, click on the control handle and hold the mouse 

button. Drag the control handle to the left or right to adjust the ratio. The values in the read-
only 

Packet parameter

 fields are updated as the slide bar is manipulated.

CODEC Information

Use the Up-arrow and Down-arrow to configure the Codecs on the Configuration list.
Select the Codec(s) to be applied for voice transmission by highlighting the item on the 
Configuration list and clicking the 

>>

 button to transfer the item to the CODEC list.

Once selected, the selected CODEC(s) appear in the Packet parameters Selected field.

Summary of Contents for KX-TDA0480















































































































































































Reviews:

No comments