Panasonic KX-TC1871ALB Operating Instructions Manual Download Page 91

Page: 91 / 100

“

Useful Information

Problem

The unit does not display the
caller’s phone number.

The handset display goes to
the standby mode while
viewing the Caller List.

When a second call is
received during a
conversation, the unit does
not display the new caller’s
phone number.

(LOCATOR/INTERCOM)

does

not function.

You cannot redial by
pressing

(REDIAL/PAUSE)

(REDIAL)

You cannot have a
conversation using
the handset.

You cannot have a
conversation using
the headset.

Cause and Remedy

≥

You do not subscribe to a Caller ID service.

≥

Other telephone equipment may be
interfering with your phone. Disconnect
it and try again.

≥

Other electrical appliances connected to
the same outlet may be interfering with
the Caller ID information.

≥

Telephone line noise may be affecting
the Caller ID information.

≥

Some PABX units do not support Caller
Display.

≥

Do not pause for over 60 seconds while
searching.

≥

(DIGITAL\SP-PHONE)

was pressed.

≥

The line mode selection is incorrect.
See page 17.

≥

Your Caller ID service provider does not
support this feature.

≥

The handset is too far from the base unit.

≥

The handset is engaged in an outside
call or is viewing the Caller List/directory
list. Wait until the IN USE/CHARGE
indicator light goes out.

≥

If the last number dialled was more than
32 digits long, the number will not be
redialled correctly.

≥

Access numbers entered after pressing

(TONE)

will not be included when

redialling.

≥

When the optional headset is connected
(p. 86), you must use the headset to
talk with the caller. To have a normal
cordless phone conversation,
disconnect the headset.

≥

Make sure that the optional headset is
connected properly (p. 86).

PQQX12877ZA-6

00.8.23

10:54

y [ W 91

Summary of Contents for KX-TC1871ALB





































































































Search results

Summary of Contents for KX-TC1871ALB

Reviews:

Related manuals for KX-TC1871ALB

Brands by name

Popular brands

Panasonic KX-TC1871ALB, Operating Instructions Manual

Search results

Summary of Contents for KX-TC1871ALB

Reviews:

Related manuals for KX-TC1871ALB

Brands by name

Popular brands