Panasonic KX-PRX120W Service Manual Download Page 24

Page: 24 / 89

KX-PRX120W/KX-PRXA10W

9.1.1.

Check Power

9.1.1.1.

Check Power (Base Unit)

Is the AC Adaptor inserted into AC outlet? (*1)

Cross Reference:

Power Supply Circuit

(P.9)

Note:

(*1) Refer to

Specifications

(P.6) for part number and

supply voltage of AC Adaptor.

Is input of IC1 about 5.5 V - 8 V?

Check C32, C36 are not shorted.

Check AC Adaptor.

Check Power Supply Circuit.

Is the output voltage of IC2 about 2.85 V?

Does BBIC (IC7: 10) oscillate at 10.368 MHz?

Check X1.

Check BBIC (IC7).

Is the Collector of Q8 about 1.8 V?

Is BBIC (IC7: 62) High?

Check BBIC (IC7).

YES

Is the Collector of Q9 about 2.5 V?

YES

Is the output voltage of BBIC (IC7:44) about 3.0V?

Is the output voltage of BBIC (IC7:43) about 3.0V?

YES

Summary of Contents for KX-PRX120W


























































































Search results

Summary of Contents for KX-PRX120W

Reviews:

Related manuals for KX-PRX120W

Brands by name

Popular brands

Panasonic KX-PRX120W, Service Manual

Search results

Summary of Contents for KX-PRX120W

Reviews:

Related manuals for KX-PRX120W

Brands by name

Popular brands