Panasonic KX-MC6020C Operating Instructions Manual Download Page 9

Page: 9 / 124

1. Introduction and Installation

1.4 Overview

1.4.1 Front view

*1 The unit can hold up to approximately 100 sheets of

printed paper. Remove the printed paper before the
recording paper exit becomes full.

*2 The waste toner cartridge stores toner that is

discharged during printing. See page 107 for
information on the waste toner cartridge life.

1.4.2 Rear view

Removing the shipping tape

Remove the shipping tape (

Note:

Shipping tape positions are subject to change
without notice.

ADF (Automatic Document Feeder) cover

Document guides

Document tray

Document tray extender

Document cover

Document exit

Document entrance

Power switch

Left cover

Handset unit (optional) connection jack

Left cover open lever

Handset cord holder

Standard input tray

Front cover

Recording paper exit

Waste toner cartridge (pre-installed inside the
unit)

1 2

j k l m n

Speaker

Power inlet

Telephone line jack

External telephone jack

LAN interface connector

LED

USB interface connector

Automatic duplex unit (optional) connector

C D

Summary of Contents for KX-MC6020C





























































































































Search results

Summary of Contents for KX-MC6020C

Reviews:

Related manuals for KX-MC6020C

Brands by name

Popular brands

Panasonic KX-MC6020C, Operating Instructions Manual

Search results

Summary of Contents for KX-MC6020C

Reviews:

Related manuals for KX-MC6020C

Brands by name

Popular brands