Panasonic KX-MC6020C Operating Instructions Manual Download Page 13

Page: 13 / 124

1. Introduction and Installation

Before opening the protection bag of the new toner
cartridges, shake them vertically more than 10
times.

Remove the 4 toner cartridges from the protection
bags.

Remove the shipping tape.

Remove each protective tray (

) by lifting up the

toner cartridge (

Insert each toner cartridge (

) in the appropriate

colour slot.
From left to right, yellow, magenta, cyan, black.

Make sure that the arrows (

) match to insert

the toner cartridge correctly.

Do not touch the toner cartridge shutter at the
bottom of the toner cartridge. The toner may spill
out of the toner cartridge.

Lift the drum cartridge cover (

) and push down on

the levers (

) to close.

Push the levers down until you hear a click to
ensure that the cover is locked.

Close the front cover.

When to replace the toner cartridge and the drum
cartridge

When the display shows the following, replace the toner
cartridge.
–

“

BLACK TONER LOW

”

Summary of Contents for KX-MC6020C





























































































































Search results

Summary of Contents for KX-MC6020C

Reviews:

Related manuals for KX-MC6020C

Brands by name

Popular brands

Panasonic KX-MC6020C, Operating Instructions Manual

Search results

Summary of Contents for KX-MC6020C

Reviews:

Related manuals for KX-MC6020C

Brands by name

Popular brands