Panasonic KX-FT937LA-B, Service Manual

Page: 57 / 176

57
KX-FT937LA-B
11.1.3. Service Function Table
Code Function Set Value Effective
Range
Default Remarks
501 Pause time X 100 msec 001~600 050 ----------
502 Flash time X 10 ms 01~99 70 ----------
503 Dial speed select 1: 10 pps
2: 20 pps 1, 2 1 ----------
510 VOX time 1:6 sec 2:4 sec 1, 2 1 Setting of the end of call confirmation VOX.
511 VOX sense 1:High 2:Low 1, 2 1 When the TAM (or EXT TAM) does not stop recording
the ICM because noise is detected on the telephone
line, change this setting to “LOW”.
514 Bell detection time X 10 msec 1~9 6 ----------
520 CED frequency select 1: 2100 Hz
2: 1100 Hz 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in
The unit can copy, but can-
not transmit/receive (P.83).
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in
The unit can copy, but can-
not transmit/receive (P.83).
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when transmission
is complete.
523 Receive equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
524 Transmission equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
533 Setting the number of time that mes-
sage transfer is redialed 00~99 00~99 03 times Selects the number of times that message transfer is
redialed (not including the firsttransfer is redialed (not
including the first.
534 Setting the message transfer/paper call
redial interval 001~999 sec 001~999 065 sec Sets the interval of message transfer/pager call redial.
544 Document feed position adjustment
value set 1: 3 mm
2: 4 mm
3: 5 mm
4: 6 mm
5: 7 mm 1~5 3 If it is difficult to feed documents, raise the set value. If
multi documents feed occurs, lower the set value.
550 Memory Clear See Memory Clear Specification (P.59).
551 ROM check See Test Mode (P.54).
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See Test Mode (P.54).
553 Monitor on FAX communication select 1:OFF
2:PHASE B
3:ALL 1~3 1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
554 Modem test See Test Mode (P.54).
555 Scan check See Test Mode (P.54).
556 Motor test 00 See Test Mode (P.54).
557 LED test See Test Mode (P.54).
558 LCD test See Test Mode (P.54).
559 Document jam detection select 1:ON 2:OFF 1, 2 1 Selects the jam detection of a document during FAX
transmission/copying.
560 Cutter selection 1:ON 2:OFF 1, 2 1 Turns off the cutter function.
561 KEY test 00 See Test Mode (P.54).
562 Cutter test Press “SET” key.
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing according PBX.
571 Setting the number of times that ITS is
redialed 00~99 00~99 05times Select the number of times that ITS is redialed(not
including the first dial).
572 ITS auto redial line disconnection time
set X second 001~999 065 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of
rings 01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
580 TAM continuous tone detection 1:ON 2:OFF 1, 2 1 ON: Stops TAM operation when Dial tone, etc are
detected.
590 FAX auto redial time set X number of
times 00~99 05 Selects the number of redial times during FAX commu-
nication (not including the first dial).
591 FAX auto redial time disconnection time
set X second 001~999 065 Sets the FAX redial interval during FAX communication.