Panasonic KX-FP215, Service Manual

Page: 63 / 236

63
KX-FP215
11.1.3. Service Function Table
Code Function Set Value Effective
Range
Default Remarks
501 Pause time set
×
100 msec 001~600 035 ----------
503 Dial speed select 1: 10 pps
2: 20 pps 1, 2 1 ----------
510 VOX time 1: 6sec
2: 4sec 1, 2 1 ----------
511 VOX sense 1: High
2: Low 1, 2 1 When the TAM (or EXT TAM) does not stop recording
the ICM because noise is detected on the telephone
line, change this setting to "LOW".
514 Bell detection time
×
100 msec 1~9 6 ----------
520 CED frequency select 1: 2100 Hz
2: 1100 Hz 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in
The unit can copy, but
cannot either transmit/receive long distance or
international communications
(P.91).
521 International mode select 1: ON
2: OFF 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in
The unit can copy, but
cannot either transmit/receive long distance or
international communications
(P.91).
522 Auto standby select 1: ON
2: OFF 1, 2 1 The resolution reverts to the default when transmission
is complete.
523 Receive equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
524 Transmission equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
544 Document feed position adjustment
value set 1~9 mm 1~9 5 When the ADF function is in correct, adjust the feed
position.
550 Memory clear See Memory Clear Specification (P.65).
551 ROM check See Test Mode (P.58).
552 DTMF single tone test 1: ON
2: OFF 1, 2 2 See Test Mode (P.58).
553 Monitor on FAX communication
select 1: OFF
2: PHASE B
3: ALL 1~3 1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
554 Modem test See Test Mode (P.58).
555 Scan check See Test Mode (P.58).
556 Motor test See Test Mode (P.58).
557 LED test See Test Mode (P.58).
558 LCD test See Test Mode (P.58).
559 Document jam detection select 1: ON
2: OFF 1, 2 1 Sets whether or not to detect a paper jam. If a
document with a length longer than 600 mm is copied
or transmitted, the unit stops copying or transmitting as
a paper jamming because a document over 600 mm is
not normal. In the factory, transmitting or copying a
document longer than 600 mm is done as an aging test.
In this case, OFF is selected.
561 KEY test See Test Mode (P.58).
570 BREAK % select 1: 61%
2: 67% 1, 2 1 Sets the % break of pulse dialing according PBX.
571 ITS auto redial time set
×
number of
times
00~99 00 Selects the number of times that ITS is redialed (not
including the first dial).
572 ITS auto redial line disconnection
time set
×
second 001~999 065 Sets the interval of ITS redialing.
573 Remote turn-on ring number set
×
number of
rings
00~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
574 Dial tone detect check 1: ON
2: OFF 1, 2 2 ----------