Panasonic KX-FL513RU, Service Manual

Page: 63 / 266

6.2.3. SERVICE FUNCTION TABLE
Code Function Set Value Effective
Range
Default Remarks
501 Pause time set X 100 msec 001~600 030 ----------
502 Flash time X 10 ms 01~99 085 ----------
503 Dial speed select 1:10 pps 2:20
pps 1, 2 1 ----------
514 Bell signal detect time X 100msec 1~9 6 ----------
520 CED frequency select 1:2100 Hz
2:1100 Hz 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119).
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119).
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when
transmission is complete.
523 Receive equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 Set RX equalizer to automatic mode.
524 Transmission equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1
529 Call Service Clear
544 Selecting the document feed position 0~4mm 0~4 2 When the ADF function is incorrect, adjust the
feed position.
550 Memory clear See (P.65).
551 ROM check See (P.65).
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See (P.65).
553 Monitor on FAX communication
select 1:OFF
2:PHASE B
3:ALL 1~3 1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
554 Modem test See (P.65).
555 Scan check See (P.65).
556 Motor test 0 See (P.65).
557 LED test See (P.65).
558 LCD test See (P.65).
561 KEY test See (P.65).
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing according PBX.
571 ITS auto redial time set X number of
times 00~99 03 Selects the number of times that ITS is redialed
(not including the first dial).
572 ITS auto redial line disconnection
time set X second 001~999 065 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of
rings 01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
590 FAX auto redial time set X number of
times 00~99 03 Selects the number of redial times during FAX
communication (not including the first dial).
591 FAX auto redial time disconnection
time set X second 001~999 65 Sets the FAX redial interval during FAX
communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO 1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to (P.112).
593 Time between CED and 300bps 1:75 msec
2:500 msec
3:1 sec 1~3 1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119). Refer
to (P.113) and (P.119).
594 Overseas DIS detection select 1:detects at
the 1st time
2:detects at
the 2st time 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119). Refer
to (P.112) and (P.119).
595 Receive error limit value set 1: 5%
2: 10%
3: 15%
4: 20% 1~4 2 If the number of errors during transmission
exceeds this value, the sending side terminates
the call.
596 Transmit level set X dBm - 15~00 13 Selects the FAX transmission level. Refer to
(P.112)and (P.113).
598 Receiving sensitivity 43= -43 dBm 20~48 41 Used when there is an error problem. Refer to
(P.119).
599 ECM frame size 1:256 2:64 1, 2 1 ----------
628 H.V.P.S. check See (P.65).
63
KX-FL513RU