manualshive.com logo in svg

Panasonic K-EF134L01E, Operation Manual

Share
Download
Panasonic K-EF134L01E Operation Manual Download Page 59

                                                                           

 

 

Figure 3-35 

Please refer to the following sheet for detailed information.  

Parameter   Function  
Pack 

Duration 

Here you can select file size. Default setup is 8 minutes. 

Pre-event 

Record  

Please input pre-event record value here.  
For example, system can record the four seconds video in the buffer. 

The record begins from the fifth second.  

Disk Full 

There are two options: stop recording or overwrite the previous files 

when HDD is full. 

  Stop: Current working HDD is overwriting or current HDD is full, 

it will stop record.  

  Overwrite: Current working HDD is full; it will overwrite the 

previous file. 

Record 

Mode  

There are three modes: Auto/Manual/Off. 

Record 

Stream  

There are two options: Stream(1) and Stream(2).  

 

 

3.6  System  

 

Account (User mng.) 

3.6.1

Note: 

  For the character in the following user name or the user group name, system max supports 15-

digits. The valid string includes: character, number, and underline.  

 

56 

Summary of Contents for K-EF134L01E







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands