manualshive.com logo in svg

Panasonic K-EF134L01E, Operation Manual

Share
Download
Panasonic K-EF134L01E Operation Manual Download Page 45

                                                                           

 

Parameter  

Function  

Write Community   It is a string. It is a command between the manage process 

and the proxy process. It defined the authentication, access 

control and the management relationship between one proxy 

and one group of the managers. Please make sure the device 

and the proxy are the same.  

The read community will read/write/access all the objects the 

SNMP supported in the specified name. The default setup is 

write. 

Trap Address 

The destination address of the Trap information from the 

proxy program of the device.  

 

Trap Port  

The destination port of the Trap information from the proxy 

program of the device. It is for the gateway device and the 

client-end PC in the LAN to exchange the information. It is a 

non-protocol connection port. It has no effect on the network 

applications. It is a UDP port not TCP port. The value ranges 

from 1 to 165535. The default value is 162. 

Read-only 

Username 

Only when SNMP version is SNMP v3, you shall config this 

parameter. The default is public.  

Authentication 

Type 

Only when SNMP version is SNMP v3, you shall config this 

parameter. You can select either MD5 or SHA. The default is 

MD5.  

Authentication 

Password 

Only when SNMP version is SNMP v3, you shall config this 

parameter. Password requires min of 8 characters.  

Encryption Type 

Only when SNMP version is SNMP v3, you shall config this 

parameter. The default is CBC-DES. 

Encryption 

Password 

Only when SNMP version is SNMP v3, you shall config this 

parameter. Password requires min of 8 characters. 

Read&write 

Username 

Only when SNMP version is SNMP v3, you shall config this 

parameter. The default is private.  

Authentication 

Type 

Only when SNMP version is SNMP v3, you shall config this 

parameter. You can select either MD5 or SHA. The default is 

MD5.  

Authentication 

Password 

Only when SNMP version is SNMP v3, you shall config this 

parameter. Password requires min of 8 characters.  

Encryption Type 

Only when SNMP version is SNMP v3, you shall config this 

parameter. The default is CBC-DES. 

Encryption 

Password 

Only when SNMP version is SNMP v3, you shall config this 

parameter. Password requires min of 8 characters. 

 

 

Bonjour 

3.3.9

The Bonjour interface is shown as below. See Figure 3-19. 

 

42 

Summary of Contents for K-EF134L01E







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands