Panasonic Hybrid IP-PBX Getting Started Download Page 22 | Manualshive

Page: 22 / 22

background image

The KX-TDA15E, the KX-TDA15NE, and the KX-TDA15GR are designed to interwork with the:
• Analogue Public Switched Telephone Network (PSTN) of a European country
• Pan-European Integrated Services Digital Network (ISDN) using ISDN basic rate access

We, Panasonic Communications Company (U.K.) Ltd., declare that this equipment is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
If you would like to receive a copy of the original Declaration of Conformity of our products which relates to the
R&TTE, please visit our web address:

http://doc.panasonic.de

Panasonic Communications Co., Ltd.

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

Copyright:

This manual is copyrighted by Panasonic Communications Co., Ltd. (PCC). You may print out this manual
solely for internal use with this model. Except above, you may not reproduce this manual in any form, in
whole or part, without the prior written consent of PCC.

© 2004 Panasonic Communications Co., Ltd. All Rights Reserved.

PSQX3170ZA

KK0704TK0

«
...
20
21
22

Summary of Contents for Hybrid IP-PBX























Reviews:

No comments

Related manuals for Hybrid IP-PBX

Brand: Radio Shack Pages: 2

Brand: Hello Kitty Pages: 11

Brand: Audiovox Pages: 40

Brand: Myria Pages: 32

Brand: VTech Pages: 2

3600 Series 3618

Brand: Videx Pages: 8

Polycom VVX 310

Brand: EarthLink Pages: 4

Brand: Easydive Pages: 2

Brand: Aztech Pages: 2

Brand: Yamaha Pages: 72

U.S. Cellular Home Phone

Brand: Zte Pages: 23

Brand: Zte Pages: 13

Brand: BT Pages: 45

Brand: Barrett Pages: 133

Brand: Wheelock Pages: 4

Brand: Geemarc Pages: 48

Brand: Fanstel Pages: 27

Brand: Mitel Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands