75
Adjustments and Settings for Recording : Viewfinder Screen Status Displays
A
d
jus
tm
e
n
ts
an
d S
e
tti
ngs
f
o
r Rec
o
rd
ing
Information Item
Indication
Status
13. System information
and warnings
SYSTEM ERROR-
¢¢
TURN POWER OFF
CARD ERR
¢
REC WARNING
OVER MAX# CLIPS
BACKUP BATT EMPTY
FAN STOP
WIRELESS-RF
EOM
BOS
EOS
CANNOT REC
CANNOT PLAY
COMM ERROR
TEXT MEMO
TEXT MEMO INVALID
MARK ON/OFF
SHOT MARK INVALID
UPDATING
USB DEVICE
USB HOST
THUMBNAIL OPEN
1394 INITIAL ERROR
PROXY REC P2&SD
PROXY REC P2
NEAR END (SD)
EOM (SD)
PROXY CARD ERROR
SD CARD WRITE ERR
CLIP DISCONTINUED
CANNOT DISP IN VF
TC REGEN
SLOT SELECT
SLOT SELECT INVALID
DIR NG CARD
SLOT1/2/3/4/5
RUN DOWN CARD
SLOT1/2/3/4/5
Something abnormal is happening to the internal computer communications or
reference signal. No further recording or playback can be performed.
¢¢
is
replaced with an error code.For more information, see [Error Codes] (page 154).
P2 card has been removed while being accessed (recorded, played back, or
formatted), and subsequent operation is disabled.
An error has occurred while recording data to or playing data from a P2
card. In the actual indication the
¢
is replaced by the slot number of the P2
card that triggered the error.
Something abnormal is happening to video and/or audio being recorded.
Displayed when the maximum number of clips (1000) recorded to the P2
card is exceeded.
Backup battery needs replacing.
The fan is locked and halted.
RF signal from the wireless receiver is degraded.
P2 card has no free space.
Playback position is at the start of all the clips.
Playback position is at the end of all the clips.
The P2 card is not recordable. Detailed information is provided on the
FUNCTION screen of MODE CHECK. See the relevant section of the
MODE CHECK indication area.
Clip cannot be played back perhaps because no P2 card is loaded, or the
P2 card contains no clips.
Displayed when disconnection between microcomputers continues for a
specified period or longer.
Text memo has been added.
Text memo has not been successfully added.
Shot mark been added or deleted. For information on shot marks, see [
Shot
Mark Function
] (page 44).
This is displayed when shot marks cannot be added.
Clip information is being updated. Playback operation disabled.
AJ-HPX3000 is in USB DEVICE mode. When communication is disabled,
the indication blinks.
Indicates that the camera-recorder is set to the USB HOST mode. When the
external hard disk is not successfully recognized, then the indication blinks.
Thumbnail is being manipulated.
Displayed when the connection of the DVCPRO connector is abnormal.
Displayed when proxy recording on either the P2 card or the SD memory
card starts (when AJ-YAX800G is attached, the PROXY REC item on the
VF INDICATOR3 screen is turned on).
Displayed when proxy recording on the P2 card starts (when AJ-YAX800G is
attached, the PROXY REC item on the VF INDICATOR3 screen is turned on).
When the remaining free space on the SD Memory card drops below one
minute during proxy recording, the message is displayed (when AJ-
YAX800G is attached).
Displayed when full capacity is reached during proxy recording on the SD
memory card (when AJ-YAX800G is attached).
Displayed when proxy recording stops because of failure on either the video
encoder card or the stream.
Check the video encoder card or avoid use of
proxy recording.
(when AJ-YAX800G is attached).
Displayed when a failure occurs on the SD memory card during proxy
recording, and only recording on the SD memory card stops.(when AJ-
YAX800G is attached).
Displayed when the consistency of the combined clip is disrupted and
subsequent recordings cannot be combined in the clip when recording in
ONE CLIP REC mode.
No return video, playback, or externally input video can be output to the viewfinder.
The RET button was pressed to regenerate the time code as the time code
for the last clip recorded on a P2 card.
This blinks while the recording slots of P2 cards are switched after pressing
the USER switch where the SLOT SEL function is assigned.
This is displayed if the recording slots of P2 cards cannot be switched when
the USER switch where the SLOT SEL function is assigned is pressed.
This is displayed when the recording starts or completes while a P2 card with
an irregular directory arrangement is inserted or data are recorded after
inserting an irregular P2 card.
This is displayed when the recording starts or completes with a P2 card on
which the maximum number of overwrites has been exceeded, or when
data is recorded after inserting such a P2 card.
14. Time code indication
TCG
12:59:59:20
TCR
12:59:59:20
(V)UBG
AB CD EF 00
(V)UBR
12 34 56 78
CTL
–1:59:59:20
TCG (time code generator value)
TCR (time code reader value)
UBG VUBG (User bits generator value)
UBR VUBR (User bits reader value)
Displays CTL count.
AJ-HPX3000G(VQT1K82-5)E.book 75 ページ ２００９年１１月１２日 木曜日 午後８時１９分
