manualshive.com logo in svg

Panasonic GT02, Manual, Page: 50 / 67

Share
Download
Panasonic GT02 Manual Download Page 50

5.1.8 Error Codes 

The error codes are as follows. 

For GT01, GT11 and GT21 

Error code 

Error name 

Measures 

ER00 

BCC error 

The value of BCC may be incorrect. Check if there is no 
calculation mistake. 

ER01 

Format error 

A command format may be incorrect. Check if it is correct. 

ER02 

NOT supported error 

A command used is not supported with the version of the GT. 
Upgrade the version of the GT, or use another command. 

ER03 

Address error 

The address specified does not exist in the GT. Check the 
address of the transmitted command. 

ER04 

Receive buffer 
overflow 

The sent command exceeds the receivable number of bytes. 
Check the number of bytes of the sent command. 

ER05 

Requested overflow  

The sent readout command exceeds the number of bytes that 
can send back. Check the number of the read words. 

ER06 

Data error 

The communication condition for the GT may be unmatched 
with the condition for a destination device. Check the 
communication conditions. 

ER07 

Data write inhibit 
error 

A command for the address that writingn is not available was 
sent. Check the address of the sent command. 

 

For GT02, GT02L, GT05, GT12, GT32 and GT32-E 

Error code 

Error name 

Measures 

**0000 

BCC error 

The value of BCC may be incorrect. Check if there is no 
calculation mistake. 

**0001 

Format error 

A command format may be incorrect. Check if it is correct. 

**0002 

NOT supported error 

A command used is not supported with the version of the GT. 
Upgrade the version of the GT, or use another command. 

**0003 

Address error 

The address specified does not exist in the GT. Check the 
address of the transmitted command. 

**0004 

Receive buffer 
overflow 

The sent command exceeds the receivable number of bytes. 
Check the number of bytes of the sent command. 

**0005 

Requested overflow  

The sent readout command exceeds the number of bytes that 
can send back. Check the number of the read words. 

**0006 

Data error 

The communication condition for the GT may be unmatched 
with the condition for a destination device. Check the 
communication conditions. 

**0007 

Data write inhibit 
error 

A command for the address that writingn is not available was 
sent. Check the address of the sent command. 

Note) These are the error codes related to communicaiton. 
 

 

5.1.9 Restrictions 

Allowable bytes sent and received 

The allowable number of bytes to be sent and received in the GT is up to 512 bytes (including CR). 
Therefore, a command or response of which size is more than 513 bytes cannot be sent from the 
external device. 

Restrictions on transmitting messages 

In the two-way 2 mode, a message will not be sent if the following changes occur in the bit device. When 
readout is necessary, use the readout command. 

Number of displayed screen 
BAT bit 
Data input in progress flag 
BAT LOW flag 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for GT02




































































Reviews:

No comments