background image

Basic Instructions for the Use of This Product

  For inspection and/or repair, consult the retailer.

  Use commercial power supply from a wall socket, which is close and easily accessible to this 

Ethernet Switch.

  Unplug the power cord when installing or moving this Ethernet Switch.

  Unplug the power cord when cleaning this Ethernet Switch.

  Use this Ethernet Switch within the specifications. Deviation could lead to malfunction.

  Do not touch the twisted pair cable modular metal terminals which are connected to RJ45 

connectors (twisted pair ports) or the connectors, nor place them near electrically-charged 
objects. Static electricity could lead to equipment failure.

  Do not put the modular plug of the connected twisted pair cable on objects that can carry 

static charge, such as carpet. Do not place it in the proximity. Static electricity could lead to 
equipment failure.

  Do not put a strong shock, including dropping, to this Ethernet Switch. Deviation could lead 

to equipment failure.

  Do not store and/or use this Ethernet Switch in the environment with the characteristics listed 

below.

  (Store and/or use this Ethernet Switch in the environment in accordance with the 

specification.)

-  High humidity. Possible spilled liquid (water).
-  Dusty. Possible static charge (such as carpet).
-  Under direct sunlight.
-  Possible condensation. High/low temperature exceeding the specifications environment.
-  Strong vibration and/or strong shock.

  Please use this Ethernet Switch in place where ambient temperature is from 0 to 50

°

C.

     Failure to satisfy the conditions above may result in a fire, electric shock, equipment failure, 

and/or malfunction. Such events are not covered by the warranty.   

     Do not block the ventilator of the Ethernet Switch.
     Blocked ventilator induces the heat accumulation inside, causing equipment failure and/or 

malfunction.

  If used at a temperature out of the operating temperature range, the protection equipment 

becomes activated and the power supply stops. 

  When using two Ethernet Switches, do not stack them. When you place them side by side, 

allow for a space of 20 mm or more between them.

  When mounting Ethernet Switch to rack, leave a minimum of 20 mm space between them.

1. Please note that Panasonic shall not bear any liability whatsoever for any damages 

(this shall include, but is not limited to, lost earnings, lost opportunities, etc.)  

which were generated in relation to damages caused by operations and usage, 
or the inability to use this Ethernet Switch, whereby the customer does not follow 
this Installation Guide.

2. The contents described in this document may be changed without prior notice. For the 

latest version, please refer to the Panasonic website.

3. For any question, please contact the retailer where you purchased the product.

6

Summary of Contents for GA-AS4TPoE+ Series


















Reviews: