5
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the outdoors.
- Clean the filters and all laden surfaces on a regular basis.
- To provide protection against electric shock, connect to properly grounded outlets only.
- To reduce the risk of fire, use only metal ductwork.
- Stop using the unit when any abnormality / failure occurs and turn “OFF” the power switch or pull out the 3 pin plug.
Example of abnormality failure:
- Abnormal noise or heat.
- Abnormal emission of smell / smoke.
- Fire or oil ignition.
- Insert the Power Plug firmly, otherwise it may cause fire or electric shock.
- The supply cord must be set properly not to be damaged. The manufacturer declines all liability if the safety
standards are not observed.
- The socket used to connect the installed equipment to the electrical power supply must be within reach:
otherwise, install a mains switch to disconnect the Range Hood when required.
- The wall plugs must have a secure grip.
- The enclosed screws and wall plugs are suitable for solid brickwork or solid concrete. Suitable fasteners must be
used for other structures (e.g. plasterboard, porous concrete, porous bricks).
- The maximum length of the flue fastening screws (supplied by the manufacturer) must be 0
33
/
64
"
(13mm).
Use of non-compliant screws with these instructions can lead to danger of an electrical nature.
- Keep in mind that installations with different types of fastening systems from those supplied, or which are not
compliant, can cause electrical and mechanical seal danger.
- Clean the Power Plug regularly with dry cloth, otherwise it may cause insufficient insulation due to moisture, and
may cause fire.
- There is a fire risk if cleaning is not carried out in accordance with the instructions.
- Accessible parts may become hot when used with cooking appliances.
- Always supervise the cooking process during the use of deep-fryers:
Overheated oil can catch fire.
- A statement to the effect that when the product is to no longer be used, it must not be left in place but remove,
to prevent it from possibly failing.
- Always check that all the electrical parts (lights, exhaust device), are off when the appliance is not being used.
- This appliance is not intended for use by young children or infirm persons unless they have been adequately
supervised by a responsible person to ensure that they can use the appliance safely. Young children should be
supervised to ensure they do not play with the appliance.
- To reduce the risk of fire, electric shock, and injury to persons, Range Hood must be installed with Range Hood
Motor Unit that are marked on their cartons to indicate the suitability with this model. Other cannot be
substituted.
- To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
- Do not connect the appliance to flues (from boilers, fireplaces, etc.).
- Do not discard the packaging or any part of it, or leave it unattended.
It can constitute a suffocation hazard for children, especially the plastic bags.
- Do not flambé under the Range Hood.
- Never cook on “open” flames under the Range Hood.
- Do not leave open, unattended flames under the Range Hood.
- Do not switch “OFF” or “ON” the Range Hood when there may be a gas leak in your gas hob. Gas explosion may result in.
- Do not handle the Power Plug with wet hand, otherwise it may cause electric shock.
- Do not disassemble the unit for reconstruction.
ENGLISH
