background image

6 - ENGLISH

Standard installation dimensions (continued)

Note

 

z

This illustration assumes that the projector will be installed so that the projected image fills the screen and is 

properly aligned with it.

 

z

This drawing is not in exact scale.

SH

Image height

L4

From screen to rear of projector

SW

Image width

L5

From center of attachment plate to front of projector

SD

Projected image size

A1

From top edge of screen to top of projector

L1

Projection distance (from screen to mirror reflective 

surface*)

H1

From bottom of set (the surface in contact with this 

product) to top of projector

L2

From screen to tip of lens

L3

From screen to front of projector

* The mirror reflective surface is inside the fixed-focus lens, and is not visible from the outside.

Attention 

 

z

Install the projector with at least 500 mm (19-11/16") gap from the surrounding walls or objects in order to 

ensure that the air intake/exhaust ports of the projector will not be blocked.

 

z

Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner 

or lighting equipment (studio lamps, etc.).

 

z

Regardless of the projector model, set up the projector so that the projected image is rectangular and the 

back of the projector and the screen are parallel. Depending on your projector, however, keystone distortion 

correction via the [GEOMETRY (2D)] or [GEOMETRY] function may be possible, even after setup.  

Refer to the Operating Instructions of ET-DLE030 for details.

Note

 

z

Dimension L4 is not the distance from the projector rear panel to the wall, but the distance from the projector 

rear panel to the screen.

 

z

When [GEOMETRY (2D)], [GEOMETRY] and [KEYSTONE] are used, distance is corrected to become smaller 

than the specified image size.

 

z

The illustrations of projectors in this manual are for informational purposes only and do not represent a specific 

model. Configurations may vary with the model.

 

Dimensional relationship

 

z

H1 and L5 values

(Unit: m)

PT-RZ770 / RW730 / RZ660 / RW620 / RZ970 /  

RW930 / RX110 / RZ670 / RW630 / DZ870 / 

DW830 / DX100

PT-DZ770 / DZ680 / DZ6710 / DZ6700 / DW740 

/ DW730 / DW640 / DW6300 / DX810 / DX800 / 

DX610 / D6000 / D5000

PT-DZ780 / 

DW750 / DX820

H1

0.196

0.155

0.175

L5

0.239

0.147

0.167

 

z

L1, A1 calculation formula

(Unit: m)

Check the projected image size SD (m) and use each formula to determine projection distance (L1) and top of set 

to top edge of screen (A1).

By determining L1 and A1, you can calculate all other dimensions.

(Values obtained by the calculation formulas contain a slight error.) 

When calculating a projection distance using image size designation (value in inches), multiply the value in inches

by 0.0254 and substitute it into SD in the formula for calculating the projection distance.
In the case of PT-RZ770 / PT-RZ660 / PT-RZ970 / PT-RZ670 / PT-DZ870

For 16:10 aspect ratio

For 16:9 aspect ratio

For 4:3 aspect ratio

L1

= 0.3205 × SD + 0.0047

= 0.3294 × SD + 0.0047

= 0.3628 × SD + 0.0047

A1

= 0.1977 × SD - 0.0721

= 0.2304 × SD - 0.0721

= 0.2238 × SD - 0.0721

In the case of PT-RW730 / PT-RW620 / PT-RW930 / PT-RW630 / PT-DW830

For 16:10 aspect ratio

For 16:9 aspect ratio

For 4:3 aspect ratio

L1

= 0.3365 × SD + 0.0047

= 0.3459 × SD + 0.0047

= 0.3809 × SD + 0.0047

A1

= 0.2597 × SD - 0.0740

= 0.2942 × SD - 0.0740

= 0.2941 × SD - 0.0740

ET-PKD130B_EN_TQZJ577-7.indd   6

2017/03/13   19:04:52

Summary of Contents for ET-PKD130B



















Reviews: