Panasonic DP-180 Service Manual Download

Page: 309 / 375

309

UF-9000

APR 2006

Ver. 3.0

DP-180/190

9.5. Upper Layer

9.5.1.

DNS (Domain Name System)

The DNS (Domain Name System) protocol provides host name and IP address resolution as a service to

client applications. DNS servers enable humans to use logical node names, utilizing a fully qualified domain

name structure, to access network resources.

Domain Names are comprised of 2 or more parts, separated by dots. The part on the left is the most

specific, and the part on the right is the most general. A given device may have more than one Domain

Name but a given Domain Name points to only one device. For example, the Domain Names below:

Panasonic.com

Mail.panasonic.com

ifax.panasonic.com

can all refer to the same device, but each domain name can refer to no more than one device.

Usually, all of the devices on a given network will have the same right-hand portion of their Domain Names

(i.e. panasonic.com in the examples above). It is also possible for a Domain Name to exist but not be

connected to an actual device.

This is often done so that a group or business can have an Internet email address without having to

establish a real Internet site. In these cases, some real Internet machine must handle the email on behalf of

the listed Domain Name.

Specification for this name system follows this basic guideline.

• The name must be separated by dots and must start with ASCII code.

• Only Alpha numeric and hyphen are available.

• Up to 63 characters maximum, separated by dots.

• Up to 255 characters maximum, including all dots.

• Capital letters and small letters are not identical. (Case Sensitive.)

The advantage of using a DNS server over a host lookup table, for host name resolution, is to avoid the

need for a single centralized clearinghouse for all names. The authority for this information can be

delegated to different organizations on the network responsible for it.

There are at least 10 Root DNS servers installed all over the world.

DNS Server (root)

DNS Server

(panasonic.com)

DNS Server (jp)

DNS Server (co.jp)

DNS Server

(panafax.co.jp)

Mail Server

mlsv.panafax.co.jp

domain

DNS Name Resolution Sample

Panasonic
Device

Summary of Contents for DP-180
























































































































































































































































































































































































Search results

Summary of Contents for DP-180

Reviews:

Related manuals for DP-180

Brands by name

Popular brands

Panasonic DP-180, Service Manual

Search results

Summary of Contents for DP-180

Reviews:

Related manuals for DP-180

Brands by name

Popular brands