Panasonic DMP-BD65, Operating Instructions Manual

Page: 13 / 40

13
VQT2H94
C
o
n
n
ec
ti
o
n
s a
n
d
set
ti
n
g
s
Access Point Connection Setting
Network Easy Setting (Connection Test)
Network Easy Setting (Internet Connection Test)
≥ Refer to the operating instructions of the hub or router.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in
the Setup menu. (
> 29)
≥ You can redo these settings individually using “Network Settings”. (
>
29)
≥ Do not connect to a wireless network for which you do not have usage
rights. Wireless networks for which you do not have usage rights (SSID*
2
)
may appear during the automatic search for a wireless network
environment. However, if you connect, there is a risk that it will be
regarded as illegal access.
≥ After performing network settings on this unit, the settings (encryption
level, etc.) of the Wireless router (Access point) might change.
When you have trouble getting online on your PC, perform the network
settings on your PC in accordance with the settings of Wireless router
(Access point).
*2
This is a name given to identify specific networks among wireless LANs.
When the SSID is the same in two devices, data can be transmitted
between them.
When you experience
problems with settings
Display Check the following
A conflict with another
device occurred.
≥
Please wait a few moments,
and then try again.
A time out error
occurred. ≥ Setting of the Wireless router
(Access point) for MAC
Address etc.
≥
The signal may be weak. Using
the USB extension cable
supplied with the Wireless LAN
Adaptor, adjust the position of
the Wireless LAN Adaptor.
≥
The SSID*
2
and the encryption
key of the Wireless router
(Access point).
≥
Please wait a few moments,
and then try again.
An authentication error
or a time out error
occurred.
A device error
occurred.
≥
Connection of Wireless LAN
Adaptor
If there is no improvement in
symptom, consult your dealer.
Display
Check the
following
1. LAN cable connection or
Connection to access point
:Fail
≥ Connection of
the LAN
cables
( > 10)
2. IP address setting :Fail
3. Connection to gateway :Fail
OK
Access Point Connection Setting
Failed to connect to the access point.
A conflict with other devices occurred.
Do you wish to setup Access Point
Connection Setting again ?
Yes No
OK
Network Easy Setting (Connection Test)
Yes No
Complete.
1. LAN cable connection
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again.
Select “No” and press [OK] to finish Network
Easy Setting.
: Fail
: Fail
: Fail
1. LAN cable connection or
Connection to access point
:Pass
≥
Connection
and settings
of the hub
and router
≥ Settings of
“IP Address /
DNS
Settings”
( > 29)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection or
Connection to access point
:Pass
2. IP address setting :Pass
3. Connection to gateway :Fail
Display Check the following
Cannot find the server.
(B019)
≥ “Primary DNS” and “Secondary
DNS” settings of “IP Address /
DNS Settings” ( > 29)
Failed to connect to
the server.
(B020)
≥ The server may be busy or the
service may have been
suspended. Please wait a few
moments, and then try again.
≥
Settings of “Proxy Server
Settings” ( > 29) and the router
OK
Network Easy Setting (Internet Connection Test)
Complete.
- Connection to the Internet : Fail(B019)
Failed the connection test.
Cannot find the server.(B019)
Please refer to the operating instructions for the cause
of the error and the solution for it.
Press [OK].
VQT2H94~Body_mst.fm 13 ページ ２０１０年１月１８日 月曜日 午後２時３３分