background image

13

(EN)

Central Address Setting

* After the test operations for indoor units and outdoor units have 

fi

 nished, set the

central address.

 

This unit is not equipped with the central address setting function.

 

If using the unit in combination with central control devices (system controller, intelligent

controller, etc.) that can set the central address, set the central address using such devices.

(See “Installation Instructions” supplied with central control devices.)

 

In a case other than the above, use a wired remote controller to set the address for each group.

Set the central address according to the following procedure.

Turn on this unit again after the setting is complete.

Setting from wired remote controllers (CZ-RTC4)

Make the setting while stopped.

1

Press and hold the 2 buttons for 
several simultaneously.

A

2

3

1

2

Select the Code no. 03.

3

Select the Set data.

 

 

The indicator illuminates after blinking.
Press 

.

Setting from wired remote controllers (CZ-RTC3, CZ-RTC5, CZ-RTC5A)

1

Press and hold the 3 buttons for 
4 seconds or more simultaneously.

 

2

Select [Simple settings].

 

 

 

3

Set.

Do not change the Unit No. from the 
initial setting.
Select the Code no. 03.
Change the setting data, and set the 
central address.
Press 

 at the Unit No. selection 

position to 

fi

 nish the setting.

ENGLISH

業務用リモコン̲CZ-ANC3据付書̲En.indd 13

業務用リモコン̲CZ-ANC3据付書̲En.indd   13

2017/05/17 14:36:55

2017/05/17   14:36:55

Summary of Contents for CZ-ANC3















Reviews: