background image

19

10. Installation 

Instruction 

10.1  Select the Best Location 

10.1.1 Indoor 

Unit 

x

 

There should not be any heat source or steam near 
the unit.

x

 

There should not be any obstacles blocking the air 
circulation. 

x

 

A place where air circulation in the room is good. 

x

 

A place where drainage can be easily done. 

x

 

A place where noise prevention is taken into 
consideration. 

x

 

Do not install the unit near the door way.  

x

 

Ensure the spaces indicated by arrows from the wall, 
ceiling, fence or other obstacles.

x

 

Recommended installation height for indoor unit shall 
be at least 2.5m. 

10.1.2 Outdoor 

Unit 

x

 

If an awning is built over the unit to prevent direct 
sunlight or rain, be careful that heat radiation from the 
condenser is not obstructed. 

x

 

There should not be any animal or plant which could be 
affected by hot air discharged. 

x

 

Keep the spaces indicated by arrows from wall, ceiling, 
fence or other obstacles. 

x

 

Do not place any obstacles which may cause a short 
circuit of the discharged air. 

x

 

If piping length is over the rated length, additional 
refrigerant should be added as shown in the table below: 

Example: If the unit is installed at a 10m distance, the quantity of additional refrigerant should be 50 g. 
…… (10-7.5) m x 20g/m = 50 g 

Piping size 

Model

Gas Liquid 

Rated
Length
(m)

Max 
Elevation
(m)

Min Piping 
Length (m) 

Max 
Piping
Length
(m)

Additional
Refrigerant 
(g/m)

RE9HKE 3/8” 

1/4" 7.5 

15 

20 

RE12HKE 3/8” 1/4”  7.5 

15 

20 

11.1.3 Indoor/Outdoor Unit

Summary of Contents for CS-RE12HKE














































Reviews: