Panasonic CS-E12QD3EAW Service Manual Download Page 79

Page: 79 / 95

15.5.21 F96 (IPM Overheating)

Malfunction Decision Conditions

During operating of cooling and heating, when IPM temperature data (100°C) is detected by the IPM temperature

sensor.

Multi Models only

Compressor Overheating: During operation of cooling and heating, when the compressor OL is activated.

Heat Sink Overheating: During operation of cooling and heating, when heat sink temperature data (90°C) is

detected by the heat sink temperature sensor.

Malfunction Caused

IPM overheats due to short circuit of hot discharge air flow.

IPM overheats due to defective of outdoor fan motor.

IPM overheats due to defective of internal circuitry of IPM.

IPM overheats due to defective IPM temperature sensor.

Multi Models Only

Compressor OL connector poor contact.

Compressor

faulty.

Troubleshooting

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Summary of Contents for CS-E12QD3EAW
































































































Search results

Summary of Contents for CS-E12QD3EAW

Reviews:

Panasonic CS-E12QD3EAW, Service Manual, Page: 79 / 95

Search results

Summary of Contents for CS-E12QD3EAW

Reviews: