manualshive.com logo in svg

Panasonic CS-E12QD3EAW, Service Manual, Page: 43 / 95

Share
Download
Panasonic CS-E12QD3EAW Service Manual Download Page 43

43 

DISPOSAL OF OUTDOOR UNIT DRAIN WATER 

š

  If a drain elbow is used, the unit should be placed 

on a stand which is taller than 30 mm. 

š

  If the unit is used in an area where temperature 

falls below 0°C for 2 or 3 days in succession, it is 
recommended not to use a drain elbow, for the 
drain water freezes and the fan will not rotate. 

 

 

 

CHECK ITEMS 

 

 

  Is there any gas leakage at flare nut connections? 

 

  Is the Earth wire connection done properly? 

 

   

 

   

 

  Has the heat insulation been carried out at flare nut connections? 

 

  Is the power supply voltage complied with the rated value? 

 

   

 

   

 

  Is the connection cable being fixed firmly to the terminal board? 

 

  Is there any abnormal sound emitted? 

 

   

 

   

 

  Is the connection cable being clamped firmly? 

 

  Is the cooling / heating operation normal? 

 

   

 

   

 

  Is the drainage OK? (Refer to the “Check the Drainage” section) 

 

  Is the thermostat operation normal? 

 

   

 

   

 

   

 

  Is the Remote Control’s LCD operation normal? 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Summary of Contents for CS-E12QD3EAW
































































































Reviews:

No comments