Panasonic CF-T8 series Reference Manual Download Page 58

Page: 58 / 133

External Display

You can switch the output destination to an external display.
Connect the external display to the external display port (A).

The following are the display modes.

Do not switch using a method other than the one explained here.

Using key function

Press

or click (Start) - [Connect to a Projector].

Press

Click the display mode.

You can switch the display mode by pressing key.

NOTE

Until Windows startup is completed (during Setup Utility, etc.), the simultaneous display cannot be used and pressing

switches the display between the internal LCD and the external display.

Using Graphics Driver

Right-click the desktop, and click [Graphics Properties].

Select the display in [Operating Mode].

Click [Apply].

Switching the Display Mode

Computer only

The screen is displayed only on the internal LCD.

Duplicate

The same screen is displayed on the internal LCD and the external display.

Extend

You can use the internal LCD and the external display as an extended display area.

Projector only

The screen is displayed only on the external display.

Windows 7

Windows XP

Summary of Contents for CF-T8 series






































































































































Search results

Summary of Contents for CF-T8 series

Reviews:

Related manuals for CF-T8 series

Brands by name

Popular brands

Panasonic CF-T8 series, Reference Manual

Search results

Summary of Contents for CF-T8 series

Reviews:

Related manuals for CF-T8 series

Brands by name

Popular brands