Panasonic AWPH360N - PAN/TILT HEAD Operating Instructions Manual Download

Page: 11 / 52

- 11 -

Installation

(The installation work must be performed by your dealer without fail.)

Transmission signal selection setting

The switches on the COMP and CONNECTOR printed circuit boards must be set to
correspond to the signals to be transmitted and components to be connected to the
pan/tilt head.
(When shipped, the analog settings are supported.)

<Note>

Before setting the switches, make absolutely sure that the power of the AC adapter
which is to be connected to the pan/tilt head is set to OFF.

Analog/IEEE1394 card settings

SDI/PR switch:

WEB/1394 switch:

1394

WEB/RP 422 switch: RP 422

SDI settings

SDI/PR switch:

SDI

WEB/1394 switch:

1394

WEB/RP 422 switch: RP 422

WEB card settings

SDI/PR switch:

WEB/1394 switch:

WEB

WEB/RP 422 switch: WEB

COMP printed circuit board

PB switch
Do not change the setting of this
switch — use it at the PB position.

COMP switch

SDI/PR switch

CONNECTOR printed circuit board

WEB/1394 switch

WEB/RP 422 switch

Summary of Contents for AWPH360N - PAN/TILT HEAD





















































Search results

Summary of Contents for AWPH360N - PAN/TILT HEAD

Reviews:

Related manuals for AWPH360N - PAN/TILT HEAD

Brands by name

Popular brands

Panasonic AWPH360N - PAN/TILT HEAD, Operating Instructions Manual

Search results

Summary of Contents for AWPH360N - PAN/TILT HEAD

Reviews:

Related manuals for AWPH360N - PAN/TILT HEAD

Brands by name

Popular brands