background image

19

Mounting the camera on a tripod

Use the tripod adaptor, available as an optional accessory, 
to mount the camera on a tripod.

1

  Mount the tripod adaptor on the tripod.

Select the appropriate holes from among the 
holes on the bottom of tripod adaptor depending 
on where the centre of gravity of the camera 
and tripod adaptor falls. If the holes selected are 
not appropriate, the centre of gravity will not be 
supported, as a result of which the camera may 
drop off or fall over, which in turn may possibly 
cause injury. 
Check that the diameter of the holes selected for 
mounting matches the diameter of the screw holes 
of the tripod platform. If these diameters do not 
correspond, the tripod adaptor will not be secured 
properly, as a result of which the camera may drop 
off or fall over, which in turn may possibly cause 
injury.

Note

Tripod platform

Tripod adaptor

2

   Mount the camera on the tripod adaptor. Slide the 

camera toward the front along the groove until a click is 
heard. 
Now check that the camera is secured properly.

Detaching the camera from the tripod adaptor
While pushing the red lever, move the black lever in the 
direction of the arrow, and slide the camera toward the 
back.

Red lever

Tripod adaptor

Black lever

<Note>

If the pin of the tripod adaptor fails to return to its original 
position after the camera has been detached, push the 
red lever again and simultaneously move the black lever 
in the direction of the arrow to return the pin to its original 
position.
Bear in mind that the camera cannot be mounted if the 
pin still remains at the centre.

Concerning the steps for ensuring that the 
camera does not slip or drop out of position

When installing the camera on a crane or at some 
other position high above the floor or ground, first 
check that the crane can bear the weight of the entire 
system including the camera, lens and connecting 
cables, and then use the specified tools to install the 
camera securely.
Be absolutely sure to ensure that the camera will not 
drop from its position by looping an anti-drop wire 
around its handle and securing the end of the wire at a 
point above the camera, as shown in the figure below.

Note

Anti-drop wire

Summary of Contents for AK-HC3500AES

















































Reviews: