Panasonic AJ-HPM200P Operation Instruction Manual Download Page 57

Page: 57 / 230

C
lip

nag

eme

Clip Management: Continuous Playback of Clips by Inserting/Removing P2 Cards

Continuous Playback of Clips by Inserting/Removing P2 Cards

All the clips, including those in the P2 card inserted during

playback, can be played continuously. If a P2 card is removed

during playback, the clips in that card are not played back.

Open the thumbnail screen.

The thumbnail screen appears on the LCD monitor.

Press the MENU button.

Use the cursor buttons to choose [THUMBNAIL] –

[CONTINUOUS PB CLIPS] and press the SET

button.

The thumbnails of the first clip in each slot appear on the

upper half of the thumbnail screen. The thumbnails of the

clips in all the slots appear in order of slots on the lower

half of the thumbnail screen.

◆

NOTE:

• Press the EXIT button to move the cursor to the upper half of the

thumbnail screen. Press the SET button to move the cursor to

the lower half of the thumbnail screen.

• The SPANNED indicator is displayed as a thumbnail when a P2

card includes only clips connected to another P2 card.

• When CONTINUOUS PB CLIPS is selected, if the thumbnail list

screen is exited by pressing the THUMBNAIL button and

removing the P2 card, the CONTINUOUS PB CLIPS thumbnail

screen is resumed if you press the THUMBNAIL button.

• To cancel CONTINUOUS PB CLIPS mode, select a display

mode other than [CONTINUOUS PB CLIPS] on the

[THUMBNAIL] menu.

Place the cursor on the clip you want to play back

then press the PLAY

button.

Playback starts from the clip at the cursor position.

When playback starts from a clip indicated on the upper

half of the thumbnail screen, playable clips will be played

back continuously from those in the slot at the cursor

position to those in slot 6, in order.

When playback starts from a clip indicated on the lower

half of the thumbnail screen, clips will be played back

continuously from the clip at the cursor position to the last

clip indicated on the thumbnail screen, in order.

If a P2 card is inserted during playback, the clips in that

card are added in the continuous playback.

FULL/FINE

MONITOR

ELECT

METER

ELECT

INPUT

ELECT

REC

THUMBNAIL

MENU

ENTRY

LOT CLIP

PF1

ALL CLIP

HIFT
PF4

CLIP LI

PF2

LOT

ELECT

T X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

CH 1

CH 2

CH 4

TEXT

MEMO

TCG

TC PRE

PROP

COUNTER

TILL/

PAU

REW

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

OURCE

ELECT

NEW

INT

REGEN

PRE

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-

PLAYLI

Displays the thumbnails of the first clip in each slot.

Blue indicates that no clips are in the slot.

Displays all clips in slot order.

Summary of Contents for AJ-HPM200P







































































































































































































































Search results

Summary of Contents for AJ-HPM200P

Reviews:

Related manuals for AJ-HPM200P

Brands by name

Popular brands

Panasonic AJ-HPM200P, Operation Instruction Manual

Search results

Summary of Contents for AJ-HPM200P

Reviews:

Related manuals for AJ-HPM200P

Brands by name

Popular brands