Panasonic AJ-HPM200P Operation Instruction Manual Download Page 120

Page: 120 / 230

120

Editing: Editing and Overwriting Clips (Rewrite Edit)

Editing and Overwriting Clips (Rewrite Edit)

Rewrite Edit is an editing method that allows you to modify a clip and overwrite it. In this section, a source clip is called a “base

clip.”

Press the PLAY LIST button to open the playlist

screen.

Switch to player operation.

Press the PLAYER button to switch to player operation.

Select a P2 card as a player.

◆

NOTE:

• Select a base clip from a P2 card only. It cannot be selected

from a hard disk or external device.

Display the player thumbnails.

During player operation, press the THUMBNAIL button to

display the thumbnails on the player screen.

Use the cursor buttons to select a clip you want to

modify and press the SET button.

The frame of the clip turns blue. Select only one clip. The

selected clip is the base clip.

Press the MENU button.

Use the cursor buttons to choose [OPERATION] –

[REWRITE EDIT] and press the SET button.

The unit enters Rewrite Edit mode, and the editing mode

indication on the timeline changes to ReW.

The playlist screen is initialized, and the selected clip is

registered on the timeline.

Perform editing.

Only overwrite editing is enabled.

After editing, use the cursor buttons to choose

[OPERATION] – [REWRITE CLIP] and press the

SET button.

Overwriting of the file starts.

Press the SET button when the confirmation dialog

appears after the progress bar has appeared and

overwriting has ended.

Rewriting of the clip created by Rewrite Edit is executed.

To exit Rewrite Edit mode, press the EDIT MODE

button or use the menu [FILE] – [NEW] to perform

initializing.

Overwrite editing mode is resumed.

OFF

METER

FULL/FINE

MONITOR

ELECT

METER

ELECT

INPUT

ELECT

REC

THUMBNAIL

MENU

ENTRY

LOT CLIP

PF1

ALL CLIP

HIFT
PF4

CLIP LI

PF2

LOT

ELECT

T X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

CH 1

CH 2

CH 4

TEXT

MEMO

TCG

TC PRE

PROP

COUNTER

PLAYER

TOP

TILL/

PAU

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

OURCE

ELECT

NEW

INT

REGEN

PRE

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-

PLAYLI

4,6,

Summary of Contents for AJ-HPM200P







































































































































































































































Search results

Summary of Contents for AJ-HPM200P

Reviews:

Related manuals for AJ-HPM200P

Brands by name

Popular brands

Panasonic AJ-HPM200P, Operation Instruction Manual

Search results

Summary of Contents for AJ-HPM200P

Reviews:

Related manuals for AJ-HPM200P

Brands by name

Popular brands