manualshive.com logo in svg

Panasonic AF7CPS Series, User Manual

Share
Download
Panasonic AF7CPS Series User Manual Download Page 49

5.3

 MEWTOCOL-COM Master Communication (SEND) 

 

5-7 

 

Timing chart 

Confirm OFF

Execute SEND

Master communication 

Sending active flag 

(YC)

Master communication

Sending done result flag 

(Y0)

Sending data

Response reception 

processing

Master communication 

Clear to send flag 

(XC)

Confirm ON

Conditions to enable execution of SEND 
instruction
Clear to send flag (XC): ON
Sending active flag (YC): OFF

Sending done result flag (Y0):
Normal completion: OFF
Abnormal completion: ON

Sending active flag (YC):
Sending data: ON, Sending done: OFF

 

 

I/O allocation 

COM port no. 1 

Name 

Explanation 

XC 

Master 
communication 
Clear to send flag 

Turns ON when MEWTOCOL-COM or  MEWTOCOL7 is set for 
the communication mode, and the unit is in the RUN mode. 

YC 

Master 
communication 
Sending active flag 

Turns ON during sending data based on SEND/RECV instruction.  
Turns OFF when the sending process is completed. 

Y0 

Sending done 
result flag 

Reports completion result of sending data in general-purpose 
communication or master communication. (Normal completion: 0, 
Abnormal completion: 1) 

(Note 1) Each contact is used for reading the operation status. Do not write over it with a user program. 

KEY POINTS

 

 

Specify the port targeted for communication, using UNITSEL instruction 
immediately before SEND/RECV instruction. 

 

Master communication is only valid when MEWTOCOL is selected. Confirm 
that the "Master communication Clear to send flag" (XC) for the targeted 
channel is ON, and execute SEND/RECV instruction. 

 

You cannot execute other SEND/RECV instruction for a communication port 
in master communication. Confirm that the "Master communication Sending 
active flag" (YC) is OFF, and execute instruction. 

 

You cannot execute SEND/RECV instruction for a port in slave 
communication. 

 

If no response is received, the "Master communication Sending active flag" 
(YC) remains ON throughout the timeout setting time specified in CPU 
configuration. 

 

Up to 16 SEND/RECV instructions can be executed simultaneously for 
different COM. ports. 

Summary of Contents for AF7CPS Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands