15 A
M4315-PRO
B LT
Blue
VOLTS
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5. WARNING:
Do not use this apparatus near water. To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
6. CAUTION
- Contains Always On Receptacles. To reduce risk of shock - Disconnect M4315-PRO from power source
before servicing any equipment connected to M4315-PRO.
7.
Clean only with dry cloth.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatuses that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades, with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
13.
Where the power cord is used as the main disconnect device, the disconnect device shall remain readily accessible.
14.
This device must be connected to a main socket outlet with a protective earthing connection.
BEFORE YOU BEGIN UNPACKING…
Inspect the unit upon receipt. In addition to this guide, the box should contain the following:
1
M4315-PRO or M4320-PRO unit
2
Four #10-24x½” Philips pan
head screws with plastic cup
washers (for rack mounting).
3
Four silicone
rubber feet (for
shelf mounting).
QSG00859 REV. G ENG
RS232
4
RS232 Card
For full instructions and warranty information visit www.panamax.com / Products /A/V Components / M4315-PRO / Manual
www.panamax.com
M4315-PRO
&
M4320-PRO
Quick Start Guide
1 2 3 4 5 6 7 8
UNSAFE VOLTAGE
BREAKER
WIRING FAULT
TEMPERATURE
15 A
OUTLET STATUS
REBOOT 1 REBOOT 2
M4315-PRO
B LT
Blue
™
VOLTS
ALWAYS ON
VOLTS / AMPS
BRIGHTNESS
M4320-PRO (20 Amp)
1.
DEFAULT OUTLET SEQUENCING (preset profile P1, by outlet #s):
With switching on and off
BREAKER or holding both
REBOOT buttons.
REBOOT 1 & 2:
Press either button for 2 seconds
to initiate a “reboot” sequence of outlet 1 or 2
(default).
Press both simultaneously for 2 seconds to initiate
a full power-up or shut down sequence. The front
panel outlet is always on, unless the circuit breaker
is set to OFF.
VOLTS/AMPS/BRIGHTNESS:
Rotate knob for
front panel brightness control, and press to toggle
the meter between VOLTS and AMPS mode.
UNSAFE VOLTAGE:
If the line voltage is less than
100 Vac or greater than 134 Vac, the outlets will
shut off and this light will flash red.
BREAKER:
Flashes red if the circuit breaker is OFF.
WIRING FAULT:
Illuminates red if the house wiring
is reverse-wired or the ground is not connected.
TEMPERATURE:
Flashes red if the internal
microprocessor temperature is greater than 60 ºC.
FRONT PANEL FEATURE OVERVIEW
These are configurations that dictate outlet sequencing timings and trigger assignments.
To change the profile:
STEP 1:
Set the circuit breaker to OFF (the
BREAKER light will flash red).
STEP 2:
Press REBOOT 1 & 2 simultaneously for 8
seconds. The meter will show the current profile:
P1-P4 (presets), or PP (personal profile). A “personal
profile” is a configuration that has been changed
from the presets by an external control (through the
COMMUNICATIONS CARD).
To change the preset profile
:
STEP 3:
Press REBOOT 1 repeatedly until the
desired profile is displayed.
STEP 4:
To select the displayed profile and exit,
press REBOOT2. To exit without changing the profile,
press REBOOT1 until “PE” (preset exit) is displayed,
then press REBOOT2. Visit www.panamax.com for
details on this procedure.
NOTE:
Users of the TCP/IP (BlueBOLT-CV1) card
may access an additional “IP” menu by pressing
REBOOT 1. Cycle past PP and P1-P4 until IP is
displayed. Pressing REBOOT2 will display the unit’s
IP address, one octet at a time.
For example, if the IP address is 192.168.1.50, then
the meter will display 192, followed in 2 seconds by
168, then 1, then 50, and terminated by ---. The
menu will then automatically exit and the unit will
return to normal operation.
If the unit has not yet obtained an IP address, the
user should wait up to 2 minutes for DHCP to assign
the address, or for the BlueBOLT-CV1 card to assign
the default address (192.168.1.169) if DHCP fails.
PROFILES
