background image

This function enables you to set a recording length
simply by pressing REC/OTR button on the TV/VCR.

Make sure . . .

Power must be turned on
Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape
to the point at which you want to begin recording.)

NOTE: This function cannot be done by the remote
control.

1 Select the channel to be recorded

Press number buttons on the remote control or the C/P
    or      button.

2 Begin OTR

Press REC/OTR button on the
TV/VCR as many times as
needed. The recording length
will be determined by the number
of times you press REC/OTR
button.
Each additional push will increase the recording time
by 30 minutes. It is set up to 8 hours. 

Display

Recording length

1 push

(normal recording)

2 pushes

30 minutes

3 pushes

1:00

60 minutes

17 pushes

480 minutes

HINTS:

Recording starts immediately when the REC/OTR
button is pressed.
When REC/OTR  button is pressed 18 times, the
TV/VCR will switch to the Normal Recording mode.
To stop the OTR operation, press STOP button on the
TV/VCR or on the remote control.
To show the remaining time, press SEL. button
repeatedly until "OTR" appears on the TV screen.
Recording stops when 0:00 is reached.
If the tape runs out before the end time, the TV/VCR
will switch to the Stop mode immediately, eject the
tape and the TV/VCR power will be turned off.

Connect your TV/VCR and a Source (Playing) VCR
using the following diagram.

(The front of
The TV/VCR)

Ex: Source
(Playing) VCR

Audio/Video
Adaptor Code
(not supplied)

(The rear of
the TV/VCR)

1) Insert a pre-recorded video cassette into the Source
    (Playing) VCR.
2) Insert a blank video cassette or one you want to record
    over, into the TV/VCR’s cassette compartment.
3) Press SPEED button to select the desired recording
    speed (SP or LP).
4) Press C/P     or      button repeatedly so that "AUX"
    appears on the screen.
5) Begin playback of the tape in the Source (Playing)
    VCR.
6) Press REC button on the TV/VCR.

NOTE:

 For best results during dubbing, use the

TV/VCR front panel controls whenever possible. The
remote control might affect the Source (Playing) VCR’s
playback operation.

18

NORMAL RECORDING

COPYING A VIDEO CASSETTE

(Requires another VCR)

Push(es)

0:30

OTR (2:30)

SP

.

.

8:00

.
.
.
.
.

.

SCART Connector
(not supplied)

Ex: Source
(Playing) VCR

Summary of Contents for TVP-342



























Reviews: