background image

The settings of picture and sound will be stored in memory until you reset them.

TELETEXT PAGE NUMBER STORE

(Please read the Teletext section before using this procedure)
The remote control unit has four colour-coded buttons. Each of these may be set to a
specific page number for Teletext. In list mode (Press PR - ), four differently coloured page
numbers are shown at the bottom of the screen. Each of these numbers may be altered and
stored in the TV's memory.
Press one of the coloured buttons on the remote control to determine which number to
change.
Enter the new page number using the number keypad.
Press the STORE button  for at least 1 second. The coloured page numbers change to
white, indicating that the number is stored in memory.
All four page numbers will be stored will be stored at the same time. If you want to change
more than one number, repeat the process for each of the colours in turn.
This process has to be repeated for each TV channel sending Teletext.

TUNING & STORING A VCR 

The set is provided with Audio/Video sockets that allow direct connection to the VCR, but
the set may also be used with the antenna connection. In this case, the VCR acts as a TV
station.
Connect the VCR and play a tape. The antenna should be connected to the VCR, and the
RF OUT from the VCR should be connected to the TV set. Read your VCR manual if you
are unsure. (The VCR takes the signal off-air from the antenna, and then acts as a TV
station which is fed to the TV set).
Open the door at the front of the TV and press the SEARCH button once. The TV set will
scan the TV bands searching for the VCR signal. This is usually at the bottom end of VHF-
1 or in UHF. Play a tape that you can recognise and ignore normal TV stations and any
weak signals. Press SEARCH again if the set finds a signal, until it finds the one you
want, It should be strong and clear.
Press STORE and attach a convenient number to the VCR channel using the PR -/+
tons. The screen should show "STORE--" in Red with the number attached. Press STORE
again to change the display to Green and make it permanent. Choose a Channel Number
that is easy to remember. You will switch to that number when you want to watch the
VCR.
Hints and Tips:
Some VCR’s have a test signal and the tape is not needed. Some VCR’S have a switch for
two channels, CH1 & CH2. Try them both and pick the clearest signal. It only takes a few
minutes. Check that the VCR channel does not interfere with the other TV channels.
The Audio/Video sockets on the back of the set may be used also.

5

Press STORE button

Press PP button

Press STORE

button again

STORE PP

STORE -

STORE PP

.

1.

2.
3.

*

*

.

.

.

.

Summary of Contents for MODEL 6738
























Reviews: